1. Turn the main power switch to ON.
2. Open the faucet on the storage
tank and place a cup or small
bucket under the faucet.
3. Turn the fan switch to OFF. This
will start a “Steam Sterilization”
cycle. Steam will now be pro-
duced in the boiling tank. The
steam will pass through the coil,
but since the fan is turned o
ff
, the steam will not be cooled. The steam will heat up
and sterilize the storage tank. Allow the distiller to run for 30-45 minutes.
4. Turn the fan switch to ON.
5. Close the faucet on the storage tank.
6. Allow the unit to
ll the storage tank and shut o
ff
.
7.
Optional Pump:
Plug the pump into the wall outlet.
8. Check for leaks.
The unit will now run automatically based on the water level in the storage tank.
Maintenance and Cleaning
Overall Maintenance Requirements
The following guide should be used for the maintenance of your distiller. The
timing will vary according to your local water conditions. It is your responsibility
to maintain your equipment. Without proper maintenance, your distiller may not
produce optimum results. The following is an average guide to maintenance:
Cleaning the Exterior
Use Stainless Steel Polish & Cleaner (stock #6606). It is available online at www.
MyAquaNui.com.
Draining the Boiling Tank
The AquaNui has a manual drain valve that discards the contaminants and residue
out of the boiling tank when opened. This minimizes the build-up of scale in the
boiling tank.
3. Connect the 5” piece of tubing to the outlet of the Carbon Filter.
4. Connect the remaining 1/4” tubing to the saddle tapping valve.
3. Connect the 1/4” tubing from the saddle tapping valve to the inlet of the carbon
lter.
4. Rinse the carbon
lter:
a. Hold the outlet end of the carbon
lter over a drain or bucket.
b. Turn the water on at the saddle-tapping valve.
c. Cycle the water on and o
ff
until the water exiting the carbon
lter is clear.
d. Turn the water supply o
ff
at the saddle-tapping valve.
5. Install 1/4” tubing from the carbon
lter outlet to the solenoid valve inlet on the
back of the distiller.
6. Turn the water supply on at the saddle-tapping valve.
Connecting the Power Cord
Note: On some 240V units, the power cord may be sold separately and is not included in
the parts kit bag.
1. Ensure the Power Switch is turned to the OFF position.
2. Locate the power cord in the parts kit bag. Install the female end of the power cord
into the outlet on the back of the unit.
Start-Up
Notes and Cautions:
Note:
This system must be fully grounded at all times. The electrical receptacle
you use must be a fully grounded, single phase, AC 115-120 volt, 15 amp (220 VAC,
7.5 amp) minimum circuit. If a two-pronged wall receptacle is encountered, it is the
personal responsibility and obligation of the customer to contact a quali
ed elec-
trician and have it replaced with a properly grounded three-pronged wall recep-
tacle or have a grounding adaptor properly grounded. If an extension cord must be
used, it should be a 3-wire, 15-amp minimum cord.
CAUTION: Do not, under any circumstances, cut or remove the round ground-
ing prong from the electrical plug.
Your unit now has:
•
A raw waterline connected and turned on.
•
A VOC pre
lter installed
•
A complete boiling tank with both water and electrical connections.
•
The storage tank faucet is installed.
•
Optional Pump:
Should not be plugged in until the storage tank is full.
Every 2 Weeks:
Drain the boiling tank.
CAUTION:
Storage tank will be very
hot. DO NOT TOUCH.
10
11
When Needed:
Clean the Exterior.
Fan Switch (ON)
Power Switch (ON)
