background image

 

Models: KPCW6 & KPCD6

Keypad Controllers

 

Installation Guide and 

Owner’s Manual 

 

 

The Inventors Of: 

CONFIGURATION 

Once your KPCx6 is installed it can be configured either 
manually or with the UPStart Setup Software.  
 
Manual configuration can be used without UPStart to add 
your KPCx6 device into a UPB network and link it to various 
load control devices.  Refer to the Keypad Controller’s Manual 
Configuration Guide available on the PulseWorx website 
(www.PulseWorx.com) for further details. 
 
Although the factory default operation of the KPCx6 is very 
useful in many situations, it is highly recommended that you 
configure your KPC with the UPStart Setup Software to take 
advantage of its many configurable features. 
 
PCS has developed a Powerline Interface Module (PIM) and 
free UPB Setup Software (UPStart) to help you configure all of 
your PulseWorx Lighting System devices.  User’s Guides are 
available on the PulseWorx web site: www.PulseWorx.com to 
explain how to configure your system. 

SETUP Mode 

When configuring a UPB system, it will be necessary to place 
the KPCx6 into SETUP mode.  To enter Setup Mode, 
simultaneously press and hold the 

ON

 and 

OFF

 buttons for 3 

seconds.  All of the LED indicators will blink once the device is 
in SETUP mode.  To exit SETUP mode, again simultaneously 
press and hold the 

ON

 and 

OFF

 buttons for 3 seconds or wait 

five minutes for it to time out. 

Changing a Scene’s Preset Light Levels 

The 6-Button Controllers are specially designed to work with 
other PulseWorx™ Lighting System devices.  Each pushbutton 
on these controllers is configured to activate a Preset Light 
Level and Fade Rate stored within the PulseWorx devices.  
The Preset Light Levels can be easily adjusted by following 
this simple procedure: 

1.

 

Press the pushbutton on the 6-Button Controller to 
activate the currently stored Preset Light Levels (scene) 
in the Wall Switch Dimmer(s). 

2.

 

Use the local rocker switch on the Wall Switch to set the 
new desired Preset Light Level. 

3.

 

Rapidly tap the pushbutton on the 6-Button Controller 

five

 times. 

4.

 

The WS1D’s lighting load will flash one time to indicate 
that it has stored the new Preset Light Level. 

OPERATION 

Once installed and configured the KPCx6 will operate with 
the stored configuration settings.  Single-tap, double-tap, 
hold, or release the pushbuttons to transmit a preset 
command onto the powerline.  Refer to the 6-Button 
Specification Document (available for download at 

www.PulseWorx.com) for more details about the keypad 
operation. 

Backlit Pushbuttons 

Each of the six pushbuttons has a blue LED behind it to provide 
back-lighting and to indicate when loads or scenes are activated.  
By default, the back-lighting is enabled and pressing a 
pushbutton will cause it to illuminate brighter than the others. 

Infra-Red (IR) Receiver 

The KPCx6 is capable of receiving IR messages from an Infra-Red 
Remote (model IRR – sold separately) to activate pushbutton 
presses from the comfort of your couch or chair. 

Keypad Lockout Feature 

A lockout feature is available to temporarily lock the keypad 
pushbuttons when throwing parties or guarding against young 
children playing with the lighting. To activate the keypad 
lockout: simultaneously press and hold the 

A

B

C

, and 

D

 

buttons for 3 seconds.  All LED indicators will extinguish and 
future presses of the buttons will have no effect.  To disable the 
keypad lockout: simultaneously press and hold the 

A

B

C

, and 

D

 

buttons again for 3 seconds.  The KPCx6 will reset and again 
respond to button presses. 

Factory Default Settings 

To restore the following default settings put the KPCx6 into 
SETUP mode and then simultaneously press and hold the 

A

 and 

D

 buttons for about 3 seconds.  The 

ON

 and 

OFF

 indicators will 

light up to indicate that factory defaults have been restored. 
 

Network ID:

 

255 

Unit ID:

 

65 

Network Password:

 

1234 

Receive Sensitivity:

 

High 

Transmit Count:

 

Twice 

IR Options:

 

IR Enabled for RM1 

LED Options:

 

Backlight enabled/ High 

ON Button Mode:

 

Link 1: On Button 

OFF Button Mode:

 

Link 2: Off Button 

A Button Mode:

 

Link 3: Link Activator 

B Button Mode:

 

Link 4: Link Activator 

C Button Mode:

 

Link 5: Link Activator 

D Button Mode:

 

Link 6: Link Activator 

UP Button Mode:

 

Last Link: Bright Button 

DN Button Mode:

 

Last Link: Dim Button 

LED Presets:

 

Standard 6-Button 

 

LIMITED WARRANTY 

Seller warrants this product, if used in accordance with all 
applicable instructions, to be free from original defects in 
materials and workmanship for a period of five years from the 
date of purchase.  Refer to the warranty information on the 
PulseWorx website (www.PulseWorx.com) for exact details. 

 

 

19201 Parthenia St.  Suite J 
Northridge, CA 91324 
(Phone) 818-701-9831 (Fax) 818-701-1506 
[email protected] www.pcslighting.com  

Reviews: