5
Table 5. Mechanical parameters
Enclosure dimensions
525 x 680 x 163 + 14 [mm] (WxHxD)
Gross/Net weight
17,00 / 18,11 kg
Enclosure
Steel plate, DC01 1,0mm color white RAL 9003
Closing
Cheese head screw x 2 (at the front)
Connectors
Power supply of the cameras: RJ45 socket
Power supply for recorder: DC2,1/5,5 plug
battery output BAT: 6,3F-2,5
TAMPER output: wires
Table 6. Operation safety
Protection class PN-EN 609501:2007
I (first)
Protection grade PN-EN 60529: 2002 (U)
IP20
Electrical strength of insulation:
- between input and output circuits of the PSU (I/P-O/P)
- between input circuit and PE protection circuit (I/P-FG)
- between output circuit and PE protection circuit (O/P-FG)
3000 V/AC min.
1500 V/AC min.
500 V/AC min.
Insulation resistance:
- between input circuit and output or protection circuit
100 MΩ, 500V/DC
Declarations
CE
Table 7. Operating parameters
Operating temperature
-
10ºC...+40ºC
Storage temperature
-
20ºC...+60ºC
Relative humidity
20%...90%, without condensation
Vibrations during operation
unacceptable
Impulse waves during operation
unacceptable
Direct insulation
unacceptable
Vibrations and impulse waves during transport
According to PN-83/T-42106
2. Installation
2.1. Installation procedure
The device shall be mounted in confined spaces, according to the environment class II, with normal air humidity
(RH=90% max. without condensation) and the temperature from -
10°C to +40°C. Ensure the free flow of air around the
unit. The PSU shall work in a vertical position that guarantees sufficient convectional air-flow through ventilating holes of
the enclosure.
Before installation, prepare a Switch'a load balance. The given value of 15,4W per port is the maximum value referring to
a single output. The total power consumption should not exceed 192W when all PoE ports are being used. The increased
demand for power is particularly evident in the case of cameras with heaters or infrared illuminators - when launching
these features, the power consumption increases rapidly, which may adversely affect the operation of the switch. As the
device is designed for a continuous operation and is not equipped with a power-switch, therefore an appropriate overload
protection shall be guaranteed in the power supply circuit. Moreover, the user shall be informed about the method of
unplugging (usually through assigning an appropriate fuse in the fuse-box). The electrical system shall follow valid
standards and regulations.
2.2. Installation procedure
1. Before installation, cut off the voltage in the 230V power-supply circuit.
2. Mount the PSU in a selected location and connect the wires.
3. Connect the power cables (~230Vac) to L-N clips of the PSU.
The shock protection circuit shall be performed with a particular care, i.e. the yellow
and green wire coat of the power cable shall stick to one side of the terminal - marked
with ‘
‘
symbol on the PSU enclosure. Operation of the PSU without the properly
made and fully operational shock protection circuit is UNACCEPTABLE! It can cause a
device failure or an electric shock.
4. Connect the ground wire to the terminal marked with the
symbol (power supply module connector). Connect the
ground wire to the clip marked by the earth symbol PE. Use a three-core cable (with a yellow and green PE protection
wire) to make the connection. Lead the cables to the appropriate clips through the insulating bushing of the connection
board.
5. Connect the power (~230V).
6. Connect the battery pack according to the drawing:
- battery output (+): BAT+ cable / red,
- battery output (-): BAT
– cable / GND / black.
Caution! Connect 4x12V/17Ah batteries in series
7. Connect the camera cables to the RJ45 connectors (PoE connectors
– sockets RJ45 from 1 to 16).
