background image

ASSEMBLY INSTRUCTIONS

13. Remove the washer (HH) and nut (II) from the eye 
      bolt with rubber grommet (Q) found on the upper 
      chute crank (E).

13

E

B

Q

II

HH

14. Position the chute crank (E) so that the eye bolt with 
      rubber grommet (Q) inserts into the center hole of 
      the middle frame (B). Secure with washer (HH) and 
      nut (II).

Note:

 Do not overtighten the nut.

14

E

B

HH

II

Q

GG

Hardware Used

HH

x 1

Ф

6 × 

Ф

13 × 1 Washer

II

x 1

M6  Nut

GG

x 1

7 mm
Two-sided open-end wrench

   13

OPERATING INSTRUCTIONS

Note:

 Before using this machine, make sure that the power source you will use complies with the 

specifications detailed in this manual. Before inserting the plug into the socket, verify that the snow 
thrower’s auger and scraper are firmly attached with screws. Perform a test run to ensure that the 
rotor turns freely.

SECURING THE EXTENSION CORD

WARNING

Electric shock may cause SEVERE INJURY or DEATH. Heed these warnings:

Do not allow any part of snow thrower to make contact with water while powered on. If the 
appliance becomes wet while turned off, wipe dry before starting.
Use only a UL-rated extension cord for outdoor, all-weather use. Do not use an extension cord 
more than 150 feet (46 meters) long.
Don’t touch the appliance or its plug with wet hands or while standing in water. Wearing rubber 
boots offers some protection.

EXTENTION CORD CHART

2. To prevent the extension cord from disconnecting 
    during use, tie the female end of the extension cord 
    into a loose knot on the top right side of the middle 
    frame (B) before connecting to the male plug in the 
    switch housing (N) socket of the snow thrower.

3. Note that the snow thrower has a polarized male plug
    (O), with one prong in the switch housing (N) socket 
    slightly longer and wider than the other. The extension 
    cord female end should be likewise polarized, so that 
    the extension cord fits snugly into the switch housing 
    (N) socket.

2

3

O

P

N

N

C

Cord length is:    100 ft. (30 m)    150 ft. (46 m)
Wire gauge is:            16                     14

1. For safe and efficient use of your snow thrower, use only a UL-rated extension cord 
    recommended for outdoor use. Refer to the Extension Cord Chart below.

C

   14

Summary of Contents for PTG3418














Reviews: