3
P module power
24W max. (see fig.3)
Energy efficiency
80%
÷ 90% for full range of power and loads
Ripple voltage
20mV p-p...50mV p-p
Output current
2.0A max. (See fig.3)
Current consumption by module systems
10 mA max.
Short-circuit protection SCP and overload
protection
OLP
180% - 200% of module power - output power limit,
automatic return after elimination of short circuit
Technical outputs
- AW output indicating failure
- OC type, 50mA max. Failure status: hi-Z state (high
impedance), normal status: L level (0V)
Optical indication
- IN LED indicating DC power status
- AUX LED indicating DC supply status at the output
- AWLED indicating failure
- red, normal status: is lit continuously
- green, normal status: is lit continuously
- red, normal status: does not lit, failure: is lit continuously
Operating conditions
II environmental class, -
10°C ÷40°C, ensure air flow around
the unit for convection cooling
Declarations, Warranties
CE, 2 years from the production date
Table 4.
Dimensions
100 x 43 x 27 (LxWxH)
Mounting
tape or mounting screw x 2
Terminals
Ф0,41÷1,63 (AWG 26-14)
Net/gross weight
0,05/0,08 kg
2. Installation.
2.1. Requirements.
The DC/DC converter is to be mounted by a qualified installer, holding relevant permits and licenses (applicable and required
for a given country) for step down
installations. The module should be mounted in confined spaces with normal relative humidity
(RH=90% maximum, no condensation) and temperature range from -
10°C up to +40°C. The module should operate in vertical position
in order to provide free and convectional air flow.
Proper operation of the module requires adequate current capacity of the power source; the power supply capacity should be
calculated using the formula below:
P
IN
= 1,15 x
P
AUX
(
P
IN
= 1,15 x
I
AUX
x
U
AUX
)
Example:
The converter will supply the receivers with a capacity of
P
AUX
= 24W
drawing a total current of
I
AUX
= 2A
at the voltage
U
AUX
= 24V
. The minimum power supply capacity must therefore amount to:
P
IN
= 1,15 x 2A x 12V = 27,6W
.
The device should be mounted in a metal enclosure (cabinet). The rules for power supply, enclosures and shielding - according to
application - must be observed in order to meet the requirements of LVD and EMC directives.
2.2. Installation procedure.
1. Mount the enclosure (cabinet, etc.) and lead cables through cable glands.
2. Mount the DC/DC converter with adhesive tape or mounting screws.
3. Supply DC voltage to the + IN, -IN terminals with correct polarization. The supply voltage should be selected according to the table
and depending on the output voltage:
4. Switch on the DC voltage.
5. Use the jumper to set the required voltage range and adjust the required output voltage with the P1 potentiometer. Default setting:
12V.
6. Switch off the DC voltage.
7. Connect the receivers’ cables to the +AUX, -AUX connectors of the terminal block on the module’s board.
8. Connect the device cables (alarm control panel, indicator, LED light, etc.) to the AW technical output if necessary.
9. Switch on the DC voltage (the red IN LED should be permanently illuminated, the AUX green LED should be permanently
illuminated).
10. Once the tests and operation control are performed, close the enclosure, cabinet, etc.
The module's load balance should be
done prior to installation. During normal
operation, the total current of the receivers should
not exceed
I=2A
while the power drawn from the
module should not exceed
Pmax=24W
, as shown
in the Fig. 3.
Fig.3. The maximum output current
depending on the output voltage.
DC input voltage
DC output voltage
8
÷28V
4,5
÷6V
12÷28V
4,5
÷9V
16
÷28V
4,5
÷13V
22
÷28V
4,5
÷19V
