background image

PIM90.241

Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN

www.pulspower.com

15 / 17

All parameters are specified at 24V, 3.8A, 230Vac, 25°C ambient and after a 5 minutes run-in time unless otherwise noted.

18. Approved, Fulfilled or Tested Standards

IEC 61010

CB Scheme Certificate
IEC 61010-2-201 - Electrical Equipment for Measurement, Control and
Laboratory Use - Particular requirements for control equipment

IEC 62368

CB Scheme Certificate
IEC 62368-1 - Audio/video, information and communication
technology equipment - Safety requirements
Output safety level: ES1

UL 61010

UL Certificate
Listed equipment for category NMTR - UL 61010-2-201 - Electrical
equipment for measurement, control and laboratory use - Particular
requirements for control equipment
Applicable for US and Canada 
E-File: E198865

IEC 61558-2-16
(Annex BB)

Safety Isolating

Transformer

Test Certificate
IEC 61558-2-16 - Safety of transformers, reactors, power supply units
and similar products for supply voltages up to 1100V 
Particular requirements and tests for switch mode power supply units
and transformers for switch mode power supply units

ISA-71.04-1985

Manufacturer's Declaration (Online Document)
Airborne Contaminants Corrosion Test
Severity Level: G3 Harsh
H2S: 100ppb
NOx: 1250ppb 
Cl2: 20ppb
SO2: 300ppb 
Test Duration: 3 weeks, which simulates a service life of at least 10
years

VDMA 24364

Paint Wetting Impairment Substances Test (or LABS-Test)
Tested for Zone 2 and Test Class C1 according to VDMA 24364-C1-L/W
for solvents and water-based paints

19. Regulatory Product Compliance

EU Declaration of
Conformity

The CE mark indicates conformance with the European

– EMC directive
– Low-voltage directive (LVD)
– RoHS directive

REACH Regulation

Manufacturer's Declaration
EU Regulation regarding the Registration, Evaluation, Authorization
and Restriction of Chemicals
EU Regulation 1907/2006

WEEE Regulation

Manufacturer's Declaration
EU Directive on Waste Electrical and Electronic Equipment Registered
in Germany as business to business (B2B) products.
EU Directive 2012/19/EU

RoHS (China RoHS 2)

Manufacturer's Statement
Administrative Measures for the Restriction of the Use of Hazardous
Substances in Electrical and Electronic Products 25 years

EAC TR Registration

EAC Certificate
EAC EurAsian Conformity - Registration Russia, 
Kazakhstan and Belarus
 8504408200, 8504409000

Summary of Contents for PIM90.241


















Reviews: