Puls Dimension CP Series, Manual, Page: 7 / 29

CP20.245-R2
CP-Series
24V, 20A, S
INGLE
P
HASE
I
NPUT
Aug. 2022 / Rev 1.1 DS-CP20.245-R2 EN
All parameters are typ. values specified at 24V, 20A, 230Vac, 25°C ambient and after a 5 minutes run-in time unless otherwise noted.
www.pulspower.com Phone +49 89 9278 0 Germany
7/28
6. O
UTPUT
Output voltage
nom. DC 24V 23.8 - 25.2V
The device is featured with a “soft output regulation characteristic” in order to
achieve current share between multiple devices, when they are connected in parallel.
The “soft output regulation characteristic” regulates the output voltage in such a
manner that the voltage at no load is approx. 4% higher than at nominal load.
Adjustment range See chapter 24.2
Factory settings 24.1V ±0.2%, at 20A, cold unit (results to typ. 23.9V±0.2%
at 24A and typ. 25.1V±0.2% at no load)
Line regulation max. 10mV 85-300Vac
Load regulation typ. 1000mV Static value, 0A

20A; see Fig. 6-1
Ripple and noise voltage max. 100mVpp 10Hz to 20MHz, 50Ohm
Output current nom. 20A Up to 60°C ambient temperature, see Fig. 16-1
nom. 15A At 70°C ambient temperature, see Fig. 16-1
Derate linearly b60°C to +70°C, see chapter 16
PowerBoost *) nom. 24A Up to 45°C ambient temperature, see Fig. 16-1
PowerBoost decreases linearly to nominal power b45°C and +60°C, see
chapter 16
Fuse breaking current typ. 60A Up to 12ms once every five seconds, see Fig. 6-3
The output voltage stays above 20V. See chapter
24.1 for more peak current measurements.
Overload behaviour Continuous
current Output voltage > 13Vdc, see Fig. 6-1
Hiccup
PLUS ®
mode
**)
Output voltage < 13Vdc, see Fig. 6-1
Short-circuit current min. 26A ***) Load impedance <10mOhm, see Fig. 6-1
max. 31A ***) Load impedance <10mOhm, see Fig. 6-1
max. 9.8A ***)
Average (R.M.S.) current, load impedance 50mOhm,
see Fig. 6-2.
min. 55A Up to 12ms, load impedance <10mOhm, see Fig. 6-3
typ. 70A Up to 12ms, load impedance <10mOhm, see Fig. 6-3
Output capacitance typ. 8 000µF Included inside the power supply
*) PowerBoost
This power/ current is continuously allowed up to an ambient temperature of 45°C.
Above 45°C, do not use this power/ current longer than a duty cycle of 10% and/ or not longer than 1 minute every 10 minutes.
**) Hiccup PLUS ® Mode
At heavy overloads (when output voltage falls below 13V), the power supply delivers continuous output current for 2s. After this, the
output is switched off for approx. 18s before a new start attempt is automatically performed. This cycle is repeated as long as the
overload exists. If the overload has been cleared, the device will operate normally. See Fig. 6-2.
***) Discharge current of output capacitors is not included.
Fig. 6-1
Output voltage vs. output current, typ.
Fig. 6-2
Short-circuit on output, Hiccup
PLUS
mode, typ.
Output Voltage
0
0 25
4
8
12
28V
16
20
24
40A 15 5 10 20 30 35
Output Current
Continuous
current
Hiccup PLUS
mode
Output
Current
0
29A
18s 18s 18s 2s 2s 2s
t
Short -circuit
Normal
operation
Normal
operation