background image

18.

  If the air inlet, floor head or the telescopic 

tube is blocked, switch off the cleaner 

straight away and remove from the main 

power. First clear the blocked object before 

attempting to start the cleaner vacuum again. 

19.

 

Do not

 leave the appliance unattended when 

it is connected to a mains power socket.

20.

 Before carry out any maintenance service 

or cleaning the filters, always switch off the 

vacuum cleaner and disconnect the plug 

from power supply.

21.

  Keep ends of the hose, telescopic tube 

and other openings away from your face 

and body.

22.

 

Do not

 use the vacuum cleaner if it is 

damaged or breaks down. Check the 

electrical regularly for defects. If connection 

cables, electrical hoses, electrical contacts 

and electric tubes are damaged, have them 

replace immediately.

23.

 

Never

 clean the vacuum cleaner or any of 

the electrical parts, especially the electrical 

connections with water or liquid cleaners.

24.

 

Never

 attempt to make any modifications 

electrically to the vacuum cleaner.

25.

  Always store the appliance indoors in a cool 

and dry place.

26.

  Damage caused by improper use or by 

not

 

observing the instructions in this manual will 

void warranty.

BEFORE YOU BEGIN

1.

 

Do not

 operate the vacuum cleaner too close to heaters, radiators, and other 

hot surfaces.

2.

  Before inserting the plug into the wall, make sure your hand is dry.

3.

   Before turning on the vacuum cleaner, remove any large or sharp objects from 

the floor or cleaning surface in order to prevent damage to the filter.

4.

  When you want to pull the plug from the wall, 

do not

 use the power cable, gently 

pull the plug from the power socket.

5.

  If the hose inlet or telescopic tube are blocked, you should switch off the cleaner 

straight away and remove from mains power. First clear the blocked substance 

before attempting to start the vacuum cleaner again.

This machine is equipped with a cable restraint, cord and plug. In the event that either of these 
parts get damaged, it must be repaired by a qualified technician.

3

PULLMAN 20L WET & DRY VACUUM WITH OUTRIGGER 

WD20LSSO

Summary of Contents for WD20LSSO

















Reviews: