background image

International Cleaning Solutions Pty. Ltd. 

ACN 119 462 798

Level 1, Building 2, Brandon Business Park 

530 Springvale Road, Glen Waverley, Victoria 3150

Pullman is a registered trademark.

Contact International Cleaning Solutions Pty. Ltd. for your 

nearest authorised service centre on 1800 815 270.

[email protected]

V1 0913

Your Pullman cleaner has a 

one year parts and labour 

warranty against product 

defects and failures when 

the product is used in 

accordance with the terms 

and conditions of this 

warranty statement.

The cleaner must be operated in accordance with 

these instructions. This cleaner is not designed for 

the collection of vitreous building material including 

particle board, construction products and similar 

products such as wood/fibres, cement, fillers, 

fibre glass etc or excessive or frequent sand. The 

infrequent pick-up of these materials in these 

circumstances may be harmful to your cleaner and 

may void the manufacturer’s warranty.
Accessories and consumables including dust bags 

and filters, unless defective in manufacture, are not 

subject to this warranty. In order to prolong the life 

of accessories and consumables, regular care and 

maintenance is recommended.
When properly used and cared for, your cleaner 

will render excellent service; refer to the instruction 

manual for further details, as misuse or failure to 

follow the instructions makes this warranty void. 

 In the event of service or advice being needed,  

please contact International Cleaning Solutions Pty 

Ltd, ACN 119 462 798, Level 1, Building 2 Brandon 

Business Park, 530 Springvale Rd, Glen Waverley, 

VIC 3150. Customer Care: 1800 815 270.
The decision to repair or replace the cleaner is at the 

sole discretion of International Cleaning Solutions 

Pty Ltd. If International Cleaning Solutions Pty Ltd 

decide to repair or replace the cleaner, it will do so 

at its own cost.
International Cleaning Solutions Pty Ltd is unable 

to accept responsibility under this warranty for 

any repair work not carried out by an authorised 

International Cleaning Solutions Service Agent or 

from the use of non-genuine parts. If any part is 

no longer available  or manufactured, International 

Cleaning Solutions will replace it with a genuine 

functional replacement part. This warranty does 

not apply to the cost of replacing any parts of the 

product due to normal wear and tear, alterations, 

improper installation, physical abuse, misuse or 

accidental damage. Any transportation costs 

involved in the repair of defective parts shall be 

borne by the claimant.
If proof of purchase cannot be provided at the time 

of a warranty claim or service, any work carried 

out on the cleaner is chargeable. The repair or 

replacement of the cleaner under this warranty 

does not extend the original period of warranty.
The benefits conferred by this warranty are 

in addition to all other rights and remedies in 

respect of the product as outlined under the 

Competition and Consumer Act and other State 

and Territory laws.
“Our goods come with guarantees that cannot 

be excluded in the Australian Consumer Law. 

You are entitled to a replacement or refund for a 

major failure and for compensation for any other 

reasonably foreseeable loss or damage. You are 

also entitled to have the goods repaired or replaced 

if the goods fail to be of acceptable quality and the 

failure does not amount to a major failure.”

Conditions of warranty

Summary of Contents for WD20LSSO

















Reviews: