PT AMC131 Hardware Manual Download Page 33 | Manualshive

Page: 33 / 108

background image

33

Chapter 3

Getting Started

This chapter provides you with information about configuring the AMC131. It includes the
following key topics:

•

“Unpacking,” on page 33

•

“System Requirements,” on page 33

•

“Memory Configuration,” on page 35

•

“Connectivity,” on page 36

•

“Switch Configuration,” on page 36

•

“Physical Installation,” on page 41

Please read this chapter before attempting to use the board.

Unpacking

Inspect the packing container for any damage. If this container appears damaged, immediately
contact the company responsible for the shipping and report the damage before opening and
unpacking the container. It is recommended that you also notify PT (see

“Customer Support

and Services,” on page 18

Caution:

To reduce the risk of damage to the AMC131, this equipment must be protected from
electrostatic discharge (EMC) and physical shock. Never remove any of the socketed parts
except in a static-free environment. Use the anti-static bag shipped with the product to
handle the module.

Caution:

Avoid touching areas of integrated circuitry. Static discharge can damage these circuits.

System Requirements

The following topics provide information about the system requirements:

•

•

Electrical and Environmental Requirements

«
...
31
32
33
34
35
...
»

Summary of Contents for AMC131













































































































Reviews:

No comments

Related manuals for AMC131

Brand: Kinderkraft Pages: 47

Brand: auna Pages: 20

Brand: Amfeltec Pages: 16

Brand: ICM Controls Pages: 2

Brand: BushBaby Pages: 2

Brand: BushBaby Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands