PT AMC123 User Manual Download Page 95

Page: 95 / 104

Mechanical Specifications

Battery Replacement

Batteries are not field serviceable items. Return the module to PT for battery replacement. See

“Return Merchandise Authorization (RMA),” on page 17

for more information about returning

merchandise.

Mechanical Specifications

The AMC123 meets the

PICMG AMC.0, R 2.0 Specification

for mechanical parameters.

Mechanical dimensions are shown in

Figure 7-1, “AMC123 Board Dimensions,”

and outlined

below.

Board Length:

180.6 mm (7.11 in)

Board Width:

73.5 mm (2.89 in)

Board Height:

19.05 mm (0.75 in) (mid-sized front panel)

Board Weight:

.295 kg (10.4 oz.) with a 2 GB DDR2, heat sink, and flash loaded

Figure 7-1:

AMC123 Board Dimensions

Reliability

The following reliability tests have been performed for the AMC123:

MTBF:

357,398 hours per Bellcore (Telecordia) SR-332 Issue 2

Contact PT for more information.

MTTR:

3 minutes

180.6 mm

73.5 mm

Summary of Contents for AMC123









































































































Search results

Summary of Contents for AMC123

Reviews:

Related manuals for AMC123

Brands by name

Popular brands

PT AMC123, User Manual

Search results

Summary of Contents for AMC123

Reviews:

Related manuals for AMC123

Brands by name

Popular brands