background image

PS Engineering 

PXE7300 Series IFE System  

Installation and Operator’s Manual 

200-973-0002 

Page 2-5 

April 2006 

means (glass cleaner, etc), and apply adhesive (supplied with antenna). Route the antenna cable along edge 
to the glareshield, and then connect to the PXE7300 connector.  Avoid running the antenna cable near 
high-current carrying wires, such as windshield heat, etc.  

The antenna cable center conductor is connected to Pin 2, braid is connected to pin B.  

2.4.5 

Unswitched Summed Audio 

PXE7300 units have four audio inputs that are summed together and presented to the audio output, J1 pin 
18 WRT V. 

NOTE: These can be used to implement additional audio warnings when connected to the appropriate 
Unswitched audio input of an audio panel. This includes Autopilot warnings, TAWS, GPS alerts, Radio 
Altimeter, etc. 

2.4.6 

Aux Entertainment Audio and AUX Enable 

Besides the disc and AM/FM, the PXE7300 has the ability to act as a switching control for an additional 
entertainment input (DVD, external XM Radio tuner, etc.).  

The audio input is Pin 16 (R), Pin 17 (L) with respect to Pin K.  

To enable the mode, add an internal jumper on the pins marked J2, or apply a ground to Pin 20 of the rear 
connector. 

2.4.7 

Special Playback Function (Option 1 only) 

The PXE7300 can be used to play up to five specially encoded audio tracks. This can be used for passenger 
briefings, tour narration, etc. These files will play automatically when a specific pin is grounded on the init 
connector, activated by a switch or logic input that pulls either to ground or to a positive voltage if the unit 
is configured properly. 

In order to use a positive voltage (>4 VDC), the unit must have jumpers installed at the following loca-
tions: 

Input 1 - R134 
Input 2 - R146 
Input 3 - R155 
Input 4 - R135 
Input 5 - R147 

Recorded MP3 files must be stored on a disc with the volume label 7300. The individual files shall be la-
beled 0001.mp3, 0002.mp3, and so on.  

The file playback is: 

Message Number 

Unit connector Pin 

Filename 

1 5 

0001.mp3 

2 9 

0002.mp3 

3 7 

0003.mp3 

4 10 

0004.mp3 

5 8 

0005.mp3 

See the operation manual for details on creating files and discs. 

 

 

 

2.5 Internal 

Adjustments 

None 

Summary of Contents for PXE7300




























Reviews: