Prusa Research Original Prusa i3 MK3S, Assembly Instructions Manual

Page: 3 / 112

3
Step 25 - Hotend fan cable adjustment (version A)
48
...............................................
Step 26 - Hotend fan assembly (version A)
48
.............................................................
Step 27 - Hotend fan assembly (version A)
49
.............................................................
Step 28 - Hotend fan parts preparation (version B)
49
...............................................
Step 29 - Hotend fan cable adjustment (version B)
49
..............................................
Step 30 - Hotend fan assembly (version B)
50
............................................................
Step 31 - Hotend fan assembly (version B)
50
.............................................................
Step 32 - Extruder-idler parts preparation (both fan versions)
50
...........................
Step 33 - Bearing assembly
51
........................................................................................
Step 34 - Extruder-idler assembly
51
.............................................................................
Step 35 - Filament alignment check
51
.........................................................................
Step 36 - Extruder-idler mounting
52
............................................................................
Step 37 - FS-cover parts preparation
52
.......................................................................
Step 38 - FS-cover assembly
53
.....................................................................................
Step 39 - Pretensioning the Extruder-idler
53
.............................................................
Step 40 - Print-fan-support parts preparation
54
.......................................................
Step 41 - Print-fan-support assembly
54
.......................................................................
Step 42 - Fan-shroud parts preparation (both fan versions)
54
................................
Step 43 - Fan-shroud assembly (both fan versions)
55
..............................................
Step 44 - Print fan parts preparation
55
........................................................................
Step 45 - Print fan assembly
55
......................................................................................
Step 46 - SuperPINDA sensor parts preparation
56
...................................................
Step 47 - SuperPINDA sensor assembly
56
.................................................................
Step 48 - Extruder parts preparation
57
........................................................................
Step 49 - Extruder preparation and mounting
57
........................................................
Step 50 - Extruder channels cable management
57
...................................................
Step 51 - X-axis belt parts preparation
58
.....................................................................
Step 52 - X-axis belt assembly
58
..................................................................................
Step 53 - X-axis belt assembly
58
..................................................................................
Step 54 - X-axis belt assembly
59
..................................................................................
Step 55 - Tensioning the X-axis belt
59
........................................................................
Step 56 - Aligning the X-axis belt
60
.............................................................................
Step 57 - Testing the X-axis belt
60
...............................................................................
Step 58 - Trimming the X-axis belt
60
..........................................................................
Step 59 - Fine tuning the x-axis belt
61
.........................................................................
Step 60 - Nylon guide parts preparation
61
..................................................................
Step 61 - Nylon guide assembly
61
.................................................................................
Step 62 - X-carriage-back parts preparation
62
..........................................................
Step 63 - Cable-holder assembly
62
..............................................................................
Step 64 - X-carriage-back assembly
62
........................................................................
Step 65 - Mounting the X-carriage-back
63
.................................................................
Step 66 - X-carriage-back assembly
63
........................................................................
Step 67 - Textile sleeve parts preparation
63
...............................................................
Step 68 - Tightening the textile sleeve
64
....................................................................
Step 69 - Guiding the hotend thermistor cables
64
....................................................
Step 70 - Tightening the hotend cables
64
...................................................................
Step 71 - Haribo time!
65
..................................................................................................
Step 72 - E-axis is finished!
65
........................................................................................
6. LCD assembly
66
...............................................................................................................
Step 1 - Tools necessary for this chapter
67
.................................................................
Step 2 - Preparing the LCD parts
67
..............................................................................
Step 3 - Checking the LCD cables
68
............................................................................
Step 4 - Assembling the LCD supports
68
...................................................................
Step 5 - Assembling the LCD-cover
68
.........................................................................