manualshive.com logo in svg

Proximus Forum 500 Series, Mounting And Commissioning Manual

The Proximus Forum 500 Series is a cutting-edge communication device that revolutionizes business collaborations. Enhance your productivity with this sleek and efficient technology. To maximize its potential, don't forget to download the free user manual from manualshive.com. Discover the endless possibilities this device has to offer.

Share
Download
background image

Installation

27

Installation

To install the Forum 5004/5008/5012 communications system, please 
perform the following steps in the order suggested.

1.

Check the scope of delivery (see 

Scope of Delivery

 on page 28), read 

Safety Precautions

 starting on page 28 and information on 

Mounting 

Location

 starting on page 32.

2.

Mount the device on the wall (see 

Wall Mounting

 starting on page 33)

3.

If multiple hardware units are being operated: configure installation 
switch(es) for additional hardware units (see 

Configuring Installation 

Switch

 starting on page 42).

4.

Connect terminals (see 

Interface Assignment, Cable Length

 starting on 

page 51)

5.

Connect the power cord to the communications system; switch on power 
supply and wait for the system to initiate (takes about 5 minutes)

6.

Connect the PC to the hardware module for initial configuration, which 
was configured as the call server with the installation switch; use LAN1 or 
LAN2 to do so

7.

Open configuration software (Configurator) in the browser (see 

Configuration

 starting on page 138); access data are:

Address (URL): http://192.168.99.254/
User: Administrator
Password: No password assigned
System PIN: 0000

8.

Loading SW Updates

 (see page 148) and if applicable 

Resetting the 

System Data

 (see page 148)

Summary of Contents for Forum 500 Series





























































































































































































































































































































































Reviews:

No comments

Related manuals for Forum 500 Series

Blaupunkt CARACAS RCR 27 Operating Instructions Manual preview
CARACAS RCR 27
Brand: Blaupunkt Pages: 15
Biamp TesiraFORTÉ AVB VT4 System Design Manual preview
TesiraFORTÉ AVB VT4
Brand: Biamp Pages: 2
TANDBERG TCP 3015A Operating Instructions Manual preview
TCP 3015A
Brand: TANDBERG Pages: 12
Danfoss ADAP-KOOL AK-SM 800 Service Manual preview
ADAP-KOOL AK-SM 800
Brand: Danfoss Pages: 4
Idemia MorphoWave SP Installation Manual preview
MorphoWave SP
Brand: Idemia Pages: 74
Poly Studio R30 User Manual preview
Studio R30
Brand: Poly Pages: 16
Binsfeld TorqueTrak Revolution Installation Manual preview
TorqueTrak Revolution
Brand: Binsfeld Pages: 2
Zenitel Phontech ICS 6200 Installation Manual preview
Phontech ICS 6200
Brand: Zenitel Pages: 193
Raven SCS 460 Operator'S Manual preview
SCS 460
Brand: Raven Pages: 47
RCA RS2022 User Manual preview
RS2022
Brand: RCA Pages: 14
NEC ASPILA EX Feature Manual preview
ASPILA EX
Brand: NEC Pages: 1098
Sharp CD-SW440N Operation Manual preview
CD-SW440N
Brand: Sharp Pages: 16
Sharp cd-pc4900 Service Manual preview
cd-pc4900
Brand: Sharp Pages: 4
Sharp CD-SW440NH Operation Manual preview
CD-SW440NH
Brand: Sharp Pages: 34
Sharp CD-SW340 Operation Manual preview
CD-SW340
Brand: Sharp Pages: 40
Sharp CD-SW300 Operation Manual preview
CD-SW300
Brand: Sharp Pages: 44
Sharp CD-SW340H Operation Manual preview
CD-SW340H
Brand: Sharp Pages: 48
Sharp CD-SW300H Operation Manual preview
CD-SW300H
Brand: Sharp Pages: 48

Brands by name

Popular brands

Load more brands