background image

 

 

15 

Section 8 

Measuring Flow Rate 

 

The voltage output by the 800 Series metering flow switches allows the flow rate of the liquid passing 
through the device to be estimated.   
 
While the flow response curves of the 800 Series metering flow switches are extremely linear, they do 
NOT pass through zero, requiring the use of a linear regression formula or calibration graphs to derive the 
actual flow rate from the measured output voltage.  
 
Calibration curves and derived look-up tables obtained from measurement of multiple sensors are shown 
below.    
 
The equations under each graph may be used with PLC or other control devices to obtain a more 
accurate measure of flow. 
 
 

Section 9  

Digital Displays 

 
Digital display units 

 
Digital panel display meters are available to provide a direct local display of flow rate in selected 
engineering units.  Each unit has a 3½ digit LCD display with 0.6-inch high digits and a DIP switch-
selectable decimal point. The digital display unit requires 4 mA at 9 to 28VDC.  
 

 

 

Flow Range 

– GPM 

Part Number 

Flow Range - LPM 

Part Number  

0.05 

– 0.3  

0G804D03 

0.2 

– 1.2 

0L804D1 

0.2 

– 2.0  

0G804D2 

0.6 

– 7.6 

0L804D7 

0.3 

– 4.5  

0G804D4 

1.2 

– 17 

0L804D17 

0.8 

– 10  

0G806D10 

– 38 

0L806D38 

1.0 

– 15  

0G808D15 

– 56  

0L808D56 

1.3 

– 19 

0G812D19 

– 72 

0L812D72 

– 50 

0G816D50 

11 

– 190 

0L816D190 

 

Table 3: Part Numbers and flow ranges for Digital Displays for the 800 Series 

 

Note 

 

Switches and potentiometers have been set to fit the range of your devices. 

Changing these settings may invalidate the calibration!  

 

 
 
Connecting the Digital Display Unit 

 

Summary of Contents for 0804BN03





















Reviews: