ProStart CT-3200 Installation Manual Download Page 21

CT-3200 

Installation Guide  

P. 21

 

16.

 

The car doesn't start and the park lights flash 4 times. 

 

Check brake circuit. 

 

Check for blown rear park light (feedback). 

17.

 

The vehicle runs for 8 seconds then shuts down. I have 12 volts on starter wire the 

whole time but no over crank. 

 

Did you make an Auto Tach Adjustment? (New GM trucks, cars and mini vans) 

18.

 

The car runs for about 5 seconds, shuts down and restarts; it does this 3 times. 

 

Check voltage on tach wire. 

 

Try an alternate tach source. 

19.

 

The car starts by remote but the range is poor. 

 

Is the car tinted? 

 

Does it have an after market alarm? 

 

Is the antenna mounted below the tint strip? 

 

Using the correct remote? 

 

Change remote battery. 

 

Heated front windshield? (Taurus, Crown Vic) 

 

Metal film in windshield? (GM Mini vans) 

 
20.

 

I get excellent range when the vehicle is not running but almost none when it is 

running. 

 

Check for loose spark plug boot or faulty ignition wires, cracked cap. 

 

Try disconnecting blower motor. 

21.

 

After about a half hour almost no range at all until the vehicle is started with the key 

again. 

 

Does the vehicle have factory alarm/ keyless entry? You might have to switch to a 
433MHZ module. (Some GM Trucks, Cavalier/Sunfire, Breeze/Stratus/Cirrus) 

22.

 

Sometimes I have to press button I twice to lock my doors. 

 

Normal on 3100/3160 if you wait past the starter kill arm cycle (approx. 35 seconds) 

 

Program toggle mode. (3100/3160 only) 

23.

 

The radio stays on after the vehicle shuts down. 

 

Retained Accessory Power will keep power to radio for approx. 10 - 15 minutes or until it 
sees a door open. (Fords, GM's R.A.P.) 

24.

 

The headlights stay on after car shuts down by remote. 

 

switch headlight switch from Auto to normal. (Toyotas) 

 

On some vehicles, opening a door will shut the head lights off. Pulse the drivers door pin 
with the Rearm wire. 

25.

 

I get no 12v reading at all at the brake pedal, depressed or not. 

 

Some vehicles require ignition be on. (BMW) 

26.

 

The park lights flash on their own. 

 

Check hood pin adjustment. 

 

Bad ground? 

27.

 

I blow fuses every time I try the remote door locks and I have already installed a relay. 

 

Door locks are reverse polarity, and not positive trigger. 

28.

 

I blow fuses every time I try the remote trunk release and I have already installed a 

relay. 

 

Trunk release is reverse polarity, and not positive trigger. 

 

Summary of Contents for CT-3200






















Reviews: