background image

 

 

 

 

d.  When the product works, the LED red, yellow and green lights are bright, 

indicating that the battery voltage is adequate; red and yellow lights are on, 
indicating insufficient voltage; only the red light is on, indicating that the battery 
is about to run out of charge and needs to be recharged.   

5. 

Accessories 

USB  cordx1,  Wrenchx1,  Ø 2.4  mm  colletx1  ,  Ø   3.2  mm  colletx1  (Assembled  in 
body), Mandrel for sanding bandx1, Mandrel for cutting wheelx1, Sanding bands x 
3,

 

Diamond bit x 1,

 

Grinding stones x 2,

 

Cutting wheels x 2,   

Sanding bands: 

To be used with mandrel for 

rough-shaping and 

smoothing metal or plastic surfaces 
 

Diamond bits: 

For fine detail work, engraving, carving, touch-up and 

finishing. Use on wood, jade, ceramic, glass, hardened steel, 
semi-precious stones and other hard materials. Bits are covered with 
diamond particles. 
 

Grinding stones:

 For surface treatment of metal parts, cast-metal parts, 

welding seams and for the removal of rust. Different shapes are available. 

 

Cutting wheel bits: 

to be used with mandrel; for removing burrs, narrow 

cuts and shaping of plastics, wood, fiberglass and soft metals. Fit the disc 
between the 2 rubber washers and tighten with the locking screw.

 

 

 

 

Wrench

: For used to secure or loosen a chuck. 

 

Cleaning and Maintenance   

Always pull out the mains power plug before starting any cleaning work. 
1. 

Cleaning 

a. 

Keep  all  safety  devices,  air  vents  and  the  motor  housing  free  of  dirt  and 
dust as far as possible. 

b. 

Wipe the equipment with a clean cloth or blow it with compressed air at low 
pressure. 

c. 

Always clean the tool after each use. 

d. 

Clean the equipment regularly with a moist cloth and some soft soap. Do 
not use cleaning agents or solvents, which may attack the plastic parts of 
the equipment. Ensure that no water can seep into the device. 

2. 

Maintenance 

There are no parts inside the equipment which require additional maintenance. 

3. 

Environmental Protection 

Waste electrical products should not be disposed of with household waste. 
Please  recycle  where  facilities  exist.  Check  with  your  Local  Authority  or 
retailer for recycling advice 

 
 

 

Summary of Contents for PT-5206U

















Reviews: