Pro's Kit MT-1707 User Manual Download

Page: 24 / 26

not be over 10 seconds. The current measurement shall be carried out 1
minute after the completion of previous measurement.

4.2.11 AC current

Measuring range

Resolution

Accuracy

60mA

0.01mA

±(1% R 3 digits)

600mA

0.1mA

10A

10mA

±(2% R 10 digits)

Overload protection:
Protective tube for mA measuring range (F500mA/250V) ; Protective

tube for 10A measuring range (F10A/250V) .

Maximal input voltage: mA position: 600mA DC/AC (valid value);

10A position: 10A DC/AC (valid value) When the

measured current is over 5A, the duration of continuous measurement shall
not be over 10 seconds. The current measurement shall be carried out 1
minute after the completion of previous measurement.
Frequency response: 40Hz-1kHz True RMS

4.2.12 Temperature (depends on different model, only for

the instruments with it)

Measuring range

Resolution

Accuracy

-20

℃

~1000

℃

(1.0% r3digits)

-4

℉

~ 1832

℉

(1.0% r3digits)

Overload protection: 600V DC/AC

5. Meter maintenance

This section provides the basic information on maintenance, including the

descriptions about replacement of protective tubes and batteries. Do not
attempt the meter maintenance unless you are experienced in maintenance

Summary of Contents for MT-1707



























Search results

Summary of Contents for MT-1707

Reviews:

Related manuals for MT-1707

Brands by name

Popular brands

Pro's Kit MT-1707, User Manual

Search results

Summary of Contents for MT-1707

Reviews:

Related manuals for MT-1707

Brands by name

Popular brands