manualshive.com logo in svg

Promotech BM-16, Operator'S Manual

Share
Download
Promotech BM-16 Operator'S Manual Download Page 18

 

BM-16 

This document is protected by copyrights. 

Copying, using, or distributing without permission of PROMOTECH is prohibited.

 

18 

Part number: 
ZBD-0509-12-00-00-0 
(includes 5 mm hex wrench) 

4.2. Anti-scratch guide sticker 

Self-adhesive  guide  sticker  against  scratches  is  dedicated  for  aluminum  bevelling. 

If the sticker is removed, clean excess glue from the guide using petroleum ether. 

 

 

 

 

 

 

 

4.3. Worktable fixture 

Designed to bevel workpieces with a width of 15

–100 mm (0.59–3.94’’), thickness of up 

to 70 mm (2.76

’’), and to the maximum bevel width of 14 mm (0.55’’). 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Install the worktable fixture by using holes in the base (

1

, Fig. 13). Then, unscrew 

the  levers  and  remove  the  vertical  clamp 

2

.  Unplug  the  machine  from  the  power 

source, r

otate the sleeve to set ‘0’ on the pitch, and then place the machine into the 

worktable fixture (

3

) so that the motor rests on the support (

4

). 

 

Part number: 
NKL-0509-05-00-00-0 

Summary of Contents for BM-16





























Reviews:

No comments

Brands by name

Popular brands

Load more brands