background image

 

 

Copyright 

Copyright by Promise Technology, Inc. (“Promise”), 1999. No part of 
this manual may be reproduced or transmitted in any form without the 
expressed, written permission of Promise. 
 

Trademarks 

All trademarks are the property of their respective holders. 
 

Important data protection information 

You should back up all data before installing any drive controller or 
storage peripheral. Promise is not responsible for any loss of data 
resulting from the use, disuse or misuse of this or any other Promise 
product. 
 

Notice 

Although Promise has attempted to ensure the accuracy of the 
content of this manual, it is possible that this document may contain 
technical  inaccuracies, typographical, or other errors. Promise 
Technology, Inc. assumes no liability for any error in this publication, 
and for damages, whether direct, indirect, incidental, consequential or 
otherwise, that may result from such error, including, but not limited to 
loss of data or profits. 
 
Promise provides this publication “as is” without warranty of any kind, 
either express or implied, including, but not limited to implied 
warranties of merchantability or fitness for a particular purpose.

 

 
The published information in the manual is subject to change without 
notice. Promise reserves the right to make changes in the product 
design, layout, and driver revisions without notification to its users. 

Summary of Contents for C6101SSWP000000-2



















Reviews: