Progressive Turf Equipment Pro-Flex 120 Operators Manual & Parts Lists Download Page 42 | Manualshive

Page: 42 / 75

background image

Pro-Flex 120 Series

Operator’s Manual

38

BELT ROUTING

FASTENER INSTALLATION TORQUE

The  chart  below  lists  the  proper  installation  torque  for  fasteners  on
Progressive Turf Equipment mowers.  When bolts are to be tightened
or replaced, refer to this chart to determine the proper torque  (unless
otherwise specified in this manual).

SAE Grade 5 (Imperial) and Class 8.8 (Metric) fasteners are to be
used in the assembly of this machine, unless otherwise specified in
this manual.

Bolt Grade / Class Identification

SAE Grade 2

SAE Grade 5

SAE Grade 8

Class 8.8

(No Dashes)

(3 Dashes)

(6 Dashes)

(Metric)

Bolt Diameter (in.)

Recommended Torque in Foot

Pounds (Newton-Meters)

5/16

21 (28)

3/8

38 (52)

7/16

55 (75)

1/2

85 (115)

9/16

125 (170)

5/8

175 (240)

3/4

300 (410)

1” LH Spindle Nut

60 (82)

M10

31 (42)

Transport Tire Nuts

100 (135)

212015

212015

212015

212011

212011

212011

212011

212013

212013

212003

«
...
40
41
42
43
44
...
»

Summary of Contents for Pro-Flex 120












































































Reviews:

No comments

Related manuals for Pro-Flex 120

Brand: Cadet Pages: 40

Brand: Lawn-Boy Pages: 32

Brand: Yazoo/Kees Pages: 42

HydroCut 5900604

Brand: Ferris Pages: 54

Brand: Poulan Pro Pages: 4

Brand: Stiga Pages: 30

Brand: Snapper Pages: 28

Brand: Yard force Pages: 11

EcoCut 135 Z-042

Brand: Talex Pages: 164

Poulan Pro 961140016

Brand: Poulan Pro Pages: 2

Brand: Cub Cadet Pages: 24

TimeCutter Z17-42

Brand: Toro Pages: 44

Brand: Cub Cadet Pages: 44

Brand: Cub Cadet Pages: 156

Brand: Giant-Vac Pages: 32

PowerMax 32 E 4033

Brand: Gardena Pages: 11

Brand: EINHELL Pages: 128

Brand: EINHELL Pages: 135

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands