Profoto RMI3 Integration Manual Download Page 16

RMI3 

16

www.profoto.com

IC Compliance Statement (Canada):

This Device complies with Industry Canada License-exempt RSS standard(s). Operation 
is subject to the following two conditions: 

1) this device may not cause interference, and 

2) this device must accept any interference, including interference that may cause 
undesired operation of the device. 

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils 
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et 

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,  
même si le brouillage est susceptible d’en compromettre le fonctionnement.

Under Industry Canada regulations, this radio transmitter may only operate using an 
antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry 
Canada.

IC RF Exposure limits

The RMI3 device complies with the IC RSS-102 radiation exposure limits set forth for 
an uncontrolled environment. For hand held operation, this device has been tested and 
meets IC RF exposure limits when the device is positioned a minimum of 1.0 cm from the 
body. For on camera mounted operation, this device has been tested and meets IC RF 
exposure limits when the device is position a minimum of 2.0 cm from the head’

Limites d’exposition R

F IC

Le dispositif RMI3 est conforme aux limites sur l’exposition aux rayonnements IC RSS-
102 définies pour un environnement non contrôlé. En mode manuel, ce dispositif a été 
testé et respecte les limites d’exposition IC RF lorsque ce dernier est placé à au moins 1 
cm du corps. Pour un fonctionnement sur caméra, ce dispositif a été testé et respecte les 
limites d’exposition RF IC lorsque ce dernier est positionné à au moins 2 cm de la tête.

Japan

Japanese Radio Law and Japanese Telecommunications Business Law Compliance.
This device is granted pursuant to the Japanese Radio Law (

電波法 

) and the Japanese 

Telecommunications Business Law (

電気通信事業法

) This device should not be 

modified (otherwise the granted designation number will become invalid).

 

R 202-SMH035

Summary of Contents for RMI3


















Reviews: