background image

3

1.

Read all instructions in this manual and all
warnings on the weight bench before using
the weight bench. Use the weight bench only
as described in this manual. 

2.

It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.

3.

The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.

4.

Keep the weight bench indoors, away from
moisture and dust. Place the weight bench
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is enough clearance around the weight
bench to mount, dismount, and use the
weight bench. 

5.   Inspect and properly tighten all parts regular-

ly. Replace any worn parts immediately. 

6.   Keep hands and feet away from moving parts.

7.

Keep children under 12 and pets away from
the weight bench at all times.

8.

Always wear athletic shoes for foot protec-
tion while exercising.

9.

The weight bench is designed to support a
maximum of 610 pounds, including a maxi-
mum user weight of 300 pounds. Do not use
more than 310 pounds of weight with the
weight bench. 

10. Always make sure that the locking pin is fully

inserted into the pivot bracket and the frame
before exercising. 

11. If you feel pain or dizziness at any time while

exercising, stop immediately and begin cool-
ing down.

WARNING:

Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. Sears assumes no responsibility for personal injury or property
damage sustained by or through the use of this product. 

WARNING: 

To reduce the risk of serious injury, read the following important precautions

before using the weight bench.

IMPORTANT PRECAUTIONS

Summary of Contents for XP 160
















Reviews: