32. Wrap the Butterfly Cable (83) under a 90mm
Pulley (90). Attach the Pulley and two Half Finger
Guards (133) to the Double “U”-bracket (73) with
an M10 x 47mm Bolt (136) and an M10 Nylon
Locknut (97).
33. Wrap the Butterfly Cable (83) over a “V”-pulley
(89). Attach the “V”-pulley, a Large Cable Trap
(88), and two Finger Guards (134) to the Center
Upright (37) with an M10 x 62mm Bolt (128) and
an M10 Nylon Locknut (97). Make sure the
Cable Trap is oriented to hold the Cable in the
groove of the “V”-pulley.
34. Attach the Butterfly Cable (83) to the Right Fly
Arm (43) with an M8 x 16mm Shoulder Bolt (129)
and an M8 Nylon Locknut (96). Make sure that
the Cable can pivot freely around the Bolt.
15
97
89
134
134
88
83
128
37
97
89
88
83
128
134
134
37
83
96
43
43
129
31. Wrap the Butterfly Cable (83) over a “V”-pulley
(89). Attach the “V”-pulley, a Large Cable Trap (88),
and two Finger Guards (134) to the Center Upright
(37) with an M10 x 62mm Bolt (128) and an M10
Nylon Locknut (97). Make sure the Cable Trap is
oriented to hold the Cable in the groove of the
“V”-pulley.
31
32
33
34
83
90
97
136
133
133
73
28. Attach the Butterfly Frame (42) to the Rear Top
Frame (39) with two M10 x 78mm Bolts (110), two
M10 Washers (99), and two M10 Nylon Locknuts
(97). Do not tighten the Locknuts yet.
Attach the Butterfly Frame (42) to the Center
Upright (37) with two M10 x 68mm Bolts (113),
two M10 Washers (99), and two M10 Nylon
Locknuts (97). Do not tighten the Locknuts yet.
Tighten all of the M10 Nylon Locknuts (97)
used in steps 11–28. Tighten the 1/4” x 14mm
Screws (119) used in step 22 and the 1/4” x
9.5mm Allen Head Set Screws (120) used in
step 23.
30. During cable assembly, see the CABLE DIA-
GRAMS on page 22 for cable identification
and to verify cable routing.
Locate the Butterfly Cable (83). Attach the
Cable to the Left Fly Arm (44) with an M8 x
16mm Shoulder Bolt (129) and an M8 Nylon
Locknut (96). Make sure that the Cable can
pivot freely around the Bolt.
29. Apply grease to both axles on the Butterfly Frame
(42).
Insert a Fly Arm Bushing (92) into the Right Fly
Arm (43). Wet the end of the Arm with soapy
water and slide a Fly Foam Pad (95) onto it.
Have another person slide the Right Fly Arm (43)
onto the right axle on the Butterfly Frame (42).
Note: Be careful not to confuse the Left Fly
Arm (44) with the Right Fly Arm. Make sure
that the upper end of the Arm is behind the
indicated bracket on the Butterfly Frame.
Tap two 25mm Retainer Rings (93) onto the axle of
the Butterfly Frame (42) with the included retainer
tool. Make sure that the teeth on the Retainer
Rings bend toward the tool, as shown in the
inset drawing. Tap the 25mm Round Outer Cap
(94) onto the right axle on the Butterfly Frame.
Attach the Left Fly Arm (44) in the same
manner.
14
28
39
42
99
99
97
97
97
97
37
99
110
113
29
30
43
93
94
44
42
95
92
Grease Axle
Axle
Bracket
129
96
83
44
93
42
Retainer
Tool
