ProForm 900 Elliptical Manual Download

Page: 5 / 28

ASSEMBLY

Assembly requires two persons.

Place all parts of the elliptical exerciser in a cleared area and remove the

packing materials. Do not dispose of the packing materials until assembly is completed.

In addition to the

included tools, assembly requires a Phillips screwdriver

, an adjustable

wrench

, and a rubber mallet

As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parenthe-

ses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The

number following the parentheses is the quantity needed for assembly.

IMPORTANT: Some small parts may

have been preassembled. If a part is not in the parts bag, check to see if it has been preassembled.

M4 x 16mm

Self-tapping

Screw (79)–10

M10 Spacer

(76)–2

M6 Split

Washer (88)–8

M10 x 20mm x

2mm Washer

(81)–2

M10 x 25mm x

1.5mm Washer

(83)–10

M8 x 42mm Button Bolt (71)–4

M8 Nylon

Locknut (96)–4

Wave Washer

(93)–6

M10 Split

Washer (72)–4

M4 x 65mm Screw (91)–4

M4 x 16mm

Screw (86)–4

M4 x 16mm

Flange Screw

(84)–2

M4 x 12mm

Flange Screw

(73)–6

M8 x 16mm Patch

Screw (95)–3

M10 x 23mm Patch

Screw (80)–2

M10 x 15mm Patch

Screw (82)–10

M6 x 16mm Patch

Screw (87)–8

M10 x 62mm Patch Screw (97)–2

M10 x 48mm Patch Screw (78)–2

M10 x 88mm Patch Screw (104)–2

Summary of Contents for 900 Elliptical





























Search results

Summary of Contents for 900 Elliptical

Reviews:

Related manuals for 900 Elliptical

Brands by name

Popular brands

ProForm 900 Elliptical, Manual

Search results

Summary of Contents for 900 Elliptical

Reviews:

Related manuals for 900 Elliptical

Brands by name

Popular brands