7
CHOOSING A LOCATION FOR THE RESTORATION 2.0
There are many factors to consider when choosing a location to set up the RESTORATION 2.0. These factors
vary depending on whether you use the RESTORATION 2.0 inside or outside. We have listed several factors
you may wish to consider as you decide where you want to use the RESTORATION 2.0.
If you set up the RESTORATION 2.0 inside:
1. The RESTORATION 2.0 will increase the level of
humidity in your home. The location you choose
should be well ventilated. You may need to install
a ventilation fan or use a dehumidifier.
2. The location must be close to an electrical outlet.
Do not use an extension cord with the
RESTORATION 2.0.
3. The RESTORATION 2.0 should be close to a
source of water.
4. Do not use the RESTORATION 2.0 on carpet or
other material that may be damaged by moisture.
We recommend that you place the RESTORA-
TION 2.0 on a water- and stain-resistant, non-slip
surface with a floor drain for any water that may
splash from the RESTORATION 2.0.
5. Be sure that the location you choose is stable. It
must be able to support the weight of the
RESTORATION 2.0 when it is filled with water,
plus the weight of the occupants. The RESTORA-
TION 2.0 weighs approximately 1250 pounds
when filled with water.
6. Do not use the RESTORATION 2.0 above a fin-
ished living area, due to the risk of water damage.
7. Be sure that there is room around the RESTORA-
TION 2.0 to permit servicing of the unit. The
dimensions of the spa are: 3Õ7ÓW x 7Õ6ÓL x 2Õ5ÓH.
You should allow for this size when choosing the
location.
8. The RESTORATION 2.0 is not designed for in-
floor installation. However, it is compatible with a
deck system that is built flush with the top of the
spa, provided you leave access to the motor for
service.
9. Be sure to note any other considerations, such as
aesthetics or privacy concerns, which may affect
the safety or enjoyment of using the RESTORA-
TION 2.0.
If you set up the RESTORATION 2.0 outside:
1. You should check your local building codes con-
cerning the use of outdoor spas.
2. The location must be close to an electrical outlet.
Do not use an extension cord with the
RESTORATION 2.0.
3. The RESTORATION 2.0 should be close to a
source of water.
4. We recommend that you place the RESTORA-
TION 2.0 on a water- and stain-resistant, non-slip
surface. Do not use the RESTORATION 2.0 on
rough or sharp surfaces such as gravel or wood
chips.
5. Be sure that the location you choose is stable. It
must be able to support the weight of the
RESTORATION 2.0 when it is filled with water,
plus the weight of the occupants. The RESTORA-
TION 2.0 weighs approximately 1250 pounds
when filled with water.
6. Think about environmental factors, such as rain,
wind, shade, sunlight, and so forth.
7. You should be able to monitor the use of the
RESTORATION 2.0 from your home, to prevent
unauthorized use by children. You may want to
enclose the spa with a fence and self-latching
gate to prevent unauthorized use.
8. Be sure that there is room around the RESTORA-
TION 2.0 to permit servicing of the unit. The
dimensions of the spa are: 3Õ7ÓW x 7Õ6ÓL x 2Õ5ÓH.
You should allow for this size when choosing the
location.
9. The RESTORATION 2.0 is not designed for
inground installation. However, it is compatible
with a deck system that is built flush with the top
of the spa, provided you leave access to the
motor for service.
10. Be sure to note any other considerations, such as
aesthetics or privacy concerns, which may affect
the safety or enjoyment of using the RESTORA-
TION 2.0.
