PROFILO Supurix PBT1260B, User Manual

Page: 9 / 14

13
PBT1260B-001_v01
SWEEP FUNCTION
1
Connect the unit to an appropriate outlet.
2 Press the button to turn on the electrobrush.
The electrobrush may be used on hard level
floors both with or without the cleaning pad.
On short pile carpets, the electrobrush should
be used without the cleaning pad.
3 After use turn off the electrobrush by pressing the
button.
4 To empty the waste container, lift it by the holder located
in the upper lid.
5
Push the release button located on the back of the
container to remove the waste.
6 Close the emptied waste container and refit it until it
clicks into place.
Before using the sweep function make sure
that the waste container is fitted in the unit.
Do not lift the electrobrush from the floor when
in operation.
STEAM FUNCTION
To use the steam function, follow the instructions below.
1 Match and attach the micro-fibre cloth to the cleaning pad.
Make sure that the velcros on the cleaning pad
and on the cloth fit well.
2
To fit the cleaning pad onto the unit, gently lower the
cleaning head onto the cleaning pad, so that head wheels
click into the notch in the cleaning pad. To detach the
cleaning pad, hold the pad release tab with your foot and lift
the cleaning head.
Never use the mop with the steam function
without the micro-fibre cloth attached.
3 Remove the water tank by releasing the hook of the
water tank and pulling the tank towards you.
4 Turn the water tank upside down and unscrew the cap.
Fill the tank with water, replace the cap (make sure that it is
screwed all the way in) and refit the tank.
Do not use the steam mop with the steam
function with no water in the tank.
●
Plug in the unit to an appropriate outlet.
5 Slide the HEAT switch to the ON position.
6 The unit will start heating water. The HEAT indicator light
will illuminate.
When the STEAM indicator light illuminates
the unit is ready for operation with the steam
function.
D
F
7 To start operation, press and hold the trigger.
The mop will stop steaming when you release
the trigger.
If the unit runs out of water during operation,
slide the HEAT switch to the OFF position and
refill the water tank (see sections
4
and
5
).
When the micro-fibre cloth becomes very wet
or dirty, replace it with a clean and dry one.
The micro-fibre cloth becomes very hot when
using the steam mop. Use caution when
replacing.
In order to thoroughly sanitize an area of your
floor, wait 60 seconds for the unit to heat up,
then mop the selected area with a short forward
and backward motion for about 15 seconds.
8 After use, slide the HEAT switch to the OFF position and
wait until no steam is emitted from the cleaning head.
9 Empty the water tank and unplug the unit from the outlet.
After use / Cleaning and maintenance
AFTER USE
●
When finished steam cleaning, make sure that the HEAT
switch is in the OFF position, then unplug the unit from
the outlet.
●
Pour out water from the water tank.
●
The micro-fibre cloths are machine washable (at max.
60°C).
If the cloths are very dirty, before washing soak
them in warm water with some detergent or
stain remover.
●
Thoroughly dry the cloths before storage.
REPLACING THE WATER SOFTENING FILTER
The water softening filter helps to remove minerals from
water which may impact the performance of your steam
mop. How often the filter should be replaced depends on
how hard your water is and how often you use the unit. We
suggest that you replace the water softening filter every
6 months or so.
The degree of filter contamination may impact
the performance of your steam mop.
Before replacing the filter, unplug the unit from
the outlet.
1 Remove the water tank by releasing the hook of the
water tank and pulling the tank towards you.
2 Pull the filter up and remove it from the unit.
C