6
b)
Contents of the Box
Check the contents of your box. Your new Phantom X R should include the following items in the box or your dealer
should have included these items with your purchase:
Phantom X R Bicycle
Velo Plush Saddle and Seat Post
ProdecoTech 36V 14Ah Li-ion Battery
ProdecoTech 36V 2A Li-ion Charger
Two Battery Lock Keys
Full size hex keys (2.5, 3, 4, 5, 6 & 8mm)
Philips Head #2 Screwdriver
Torx T25 Driver
c)
Registering your new bike
For the warranty to take effect, you must register your new bicycle. Registration of your electric bicycle is the only way we
can acknowledge and verify the established owner. Your bicycle has 3 individual and unique serial numbers (frame,
motor and battery). Each serial number must be registered when filling out the registration form. The serial number on
the frame is located under the crank/bottom bracket portion of the frame. The serial number for the motor is found on the
motor’s side. The serial number for the battery is located on the barcode label adhered to the underside of the battery.
These numbers should be recorded and registered in case of warranty issues or theft. Please review
Chapter 10
“Warranty Service and Repair” section c)
“Registering your bicycle” how to register your Phantom X R. You can
register by either filling out the online registration form at www.prodecotech.com/register-your-ebike/ or by sending the
registration card found in
Chapter 10 “Warranty Service and Repair” section d
)
“Registration card”.
CAUTION:
If you have purchased your bicycle by mail order or through a sales channel whereas your new
Phantom X R is still in the box, it is recommended you read Chapter 5
“Basic Instructions” section i) “Before your
first ride” prior to your first ride. There may be additional adjustments required due to shipping by the freight carrier.
d)
Unpacking your box
Your Phantom X R arrives
fully assembled in it’s box. It may require the front wheel, stem and seatpost to be installed.
To install the front wheel, read the following
section e)
Installing the front wheel. The stem installation is detailed
afterwards in
section f)
Installing the stem. You can learn how to insert the seatpost and adjust for your height in
Chapter 5
“Basic Instructions” section b)
“Adjusting the saddle”.
The Phantom X R has been tested and adjusted prior to being packageded. To remove the Phantom X R, open the top
flap of the box and remove the protective top insert. Place one hand under the front portion of the frame and the other
hand under the center of the frame. Pull up slowly and the bicycle will lift out of the box. Remove the additional inserts
and set the bicycle down by balancing the bicycle on the opened kick stand and rear wheel. The kick stand also performs
as a crankset protector.
e)
Installing the front wheel
The front wheel on the Phantom X R can be installed without tools. A quick release skewer
through a hollow axle is utilized for easy and quick wheel installation. A quick release skewer
is a rod that has a threaded acorn nut on one end and a cam lever assembly on the other
end. The cam lever applies pressure and locks the axle in place.
When installing the wheel for the first time, you must first remove the plastic brake
pad spacer as shown in the right side photo by pulling the spacer out. Follow these
instructions to install the wheel:
1. Slide the wheel axle into the fork dropouts while aligning the wheel straight.
2. Install the axle quick release skewer. With the quick release fully open, tighten the
acorn nut until a slight resistance.
Confirm axle is fully seated in the fork’s dropout.
3. Once tightened, close the quick release lever with enough force to clamp and
lock the axle into the dropouts. The force must be strong enough for the axle
not to become loose. It should take some effort to close the lever but not so
much that you are straining. Once closed, you should not be able to easily
open the quick release lever.
4. Test to see if the quick release lever will open with 1 finger. If it opens, you must
perform the previous step again until the quick release lever clamp is tight.
