ProBoat Jet Jam PRB08031 Owner'S Manual Download Page 9

•  Fully dry the inside and outside of the boat. 
•  Remove the hatch before storing your boat.
•  Repair any damage or wear to the boat.
•  Lubricate the driveshaft using ProBoat  

Marine Grease (DYNE4200).

•  Make note of lessons learned from the trimming of 

your boat, including water and wind conditions.

NOTICE: 

When you are finished boating, never leave the 

boat in direct sunlight or in a hot, enclosed area such as a 

car. Doing so can damage the boat.

After Boating and Maintenance

Binding 

The included transmitter and receiver are bound at 
the factory.

 If you need to rebind, follow the instructions 

below.

1.  Power ON the boat. The receiver LED will blink.
2.  Power ON the transmitter. The receiver LED will go 

solid, indicating it is bound.

If you encounter problems, follow binding instructions 

and refer to the troubleshooting guide for other 

instructions. If needed, contact the appropriate Horizon 

Product Support office.

NOTICE:

 Do not attempt to bind the transmitter and 

receiver if there are other compatible transmitters in 

bind mode within 400 feet. Doing so may result in 

unexpected binding.

Failsafe

 

In the unlikely event that the radio connection is lost 

during use, the receiver will drive the servos to their pre-

programmed failsafe positions as set during BINDING.
If the receiver is powered on before powering on the 

transmitter, the receiver will enter this failsafe mode. 

When the transmitter is powered on, normal control is 

resumed.

IMPORTANT:

 Failsafe activates only in the event 

that signal is lost from the transmitter. Failsafe will 

NOT activate in the event that receiver battery power 

decreases below the recommended minimums or 

power to the receiver is lost.

•  Prolong motor life by preventing overheating 

conditions. 

•  Regularly lubricate (DYNE0100) the bushings on each 

end of the motor and more frequently when the 

motor is wet. Failure to do so may cause the motor 

shaft to seize in the bushings.

•  Use water displacement fluid to flush any water from 

the motor compartment.

Motor Care

9

EN

12-INCH READY-TO-RUN POOL RACER

Summary of Contents for Jet Jam PRB08031
















Reviews: