background image

10

(4) Attach the USB cover to fix the USB 

cable. Insert the USB cover into the tab 
of the USB holder.

• Check the up/down orientation of the 

USB cover to ensure that the USB 
cable is secured properly.

„

Removing the USB Holder

(1) Lift up the tab of the USB holder and 

then remove the USB cover as shown 
below.

(2) After removing the USB cable, remove 

the picks pushing the USB holder from 
both top and bottom.

UL/c-UL Approval

The ST-3400 Series units are UL/c-UL listed 
products.

(UL File No.E220851)

These products conform to the following 
standards:

„

UL508

Industrial Control Equipment

„

CSA-C22.2 No.142-M1987 

 

(c-UL Approval)

Process Control Equipment

<Cautions>

Be aware of the following items when 
building the ST into an end-use product:

• The ST unit’s rear face is not approved as 

an enclosure. When building the ST unit 
into an end-use product, be sure to use an 
enclosure that satisfies standards as the 
end-use product’s overall enclosure.

• The ST unit must be used indoors only.
• Install and operate the ST with its front 

panel facing outwards.

• If the ST is mounted so as to cool itself 

naturally, be sure to install it in a vertical 
panel. Also, it’s recommended that the ST 
should be mounted at least 100mm away 
from any other adjacent structures or 
machine parts. The temperature must be 
checked on the final product in which the 
ST is installed.

• For use on a flat surface of a Type 4X 

(Indoor Use Only) and/or Type 13 Enclo-
sure.

USB Holder

Tab

USB Cover

USB Holder

Tab

USB Cover

Product Model No.

UL/c-UL 

Registration Model No.

AST3401-T1-D24

3580206-01

Summary of Contents for ST-3400 Series












Reviews: