background image

3

„

Environmental Specifications

„

External Specifications

Serial Interface Specifications

„

RS-232C Isolation Unit

The RS-232C/RS-422 type. 

D-Sub 9-pin plug connector's pin assignments are as follows.
Use the DIP switch on the unit to change communication methods.

 

• For Display side settings please refer to “Display side settings”.

Phys

ical Envir

onment

Ambient Operating 
Temperature

0...50 °C (32...122 °F)

Storage Temperature

-20...60 °C (-4...140 °F)

Ambient  and Storage 
Humidity

10...90 % RH (Non condensing, wet bulb 
temperature 39 °C [102.2 °F] or less)

Dust

0.1 mg/m

3

 (10

-7

 oz/ft

3

) or less (non-conductive levels)

Pollution Degree

For use in Pollution Degree 2 environment

Atmosphere

Free of corrosive gases

Atmospheric Pressure
(Operating Altitude)

800...1114 hPa (2000 m [6561 ft] or lower)

Mec

hanical 

Env

ironment

Vibration Resistance

IEC/EN 61131-2 compliant
5...9 Hz Single amplitude 3.5 mm (0.14 in.)
9...150 Hz Fixed acceleration: 9.8 m/s

2

X, Y, Z directions for 10 cycles (100 min.)

Concussion Resistance

IEC/EN 61131-2 compliant
(147 m/s

2

, X, Y, Z directions for 3 times)

Elec

tr

ic

al 

En

vironment

Noise immunity

Noise Voltage: 1000 Vp-p
Pulse Width: 1 

µ

s

Rise Time: 1 ns
(via noise simulator)

Electrostatic Discharge
Immunity

Contact Discharge Method: 6 kV (IEC/EN61000-4-2 
Level 3)

Cooling Method

Natural air circulation

Weight

170 g (0.37 lb) or less 

External
Dimensions

W110 x H40 X D27 mm (W4.33 x H1.57 x D1.06 in.)

RS232C

RS422

Summary of Contents for RS-232C









Reviews: