background image

T15K

GENERAL PRECAUTIONS 

(cont.)

DRILLING SAFETY

•  Inspect the area to be drilled before operation. Remove objects which can be thrown or be-

come entangled. 

•  Keep all parts of your body away from the drilling bit when operating the unit. 
•  DO NOT operate the PRO-DIG

® 

Auger Drive when the auger bit is more than 12” (305mm) 

above ground. The auger bit may bind and cause injury to the operator and damage to the 
equipment. 

•  While the auger bit is rotating, DO NOT attempt to manually guide the auger to a location.

UNDERGROUND HAZARDS

It is the responsibility of the operator to know where buried power, gas, telephone, and other utili-
ties are in the work area. This may lead to shock or an explosion. Have the work area marked for 
buried lines and do not dig in marked areas set by your local municipals. Striking a hard object 
underground with the auger turning can result in the slowing or stopping of the auger.

SAFETY DECAL LOCATIONS

SAFETY DECALS

This unit comes equipped with all safety decals in place. They are designed to help you safely 
operate your unit. Read and follow all safety decals.
(Locations shown below in figure 1)

• 

Keep all safety decals clean and legible at all times

•  Replace safety decals that are missing or have become illegible. 
•  Safety decals are available from your distributor or manufacture.
•  Some parts installed during repair may require safety decals to be affixed to the replacement 

part. When ordering the replacement part(s) be sure the correct safety decal(s) are included in 
your order.

INSTALLING SAFETY DECALS

• 

Clean the desired are with warm soapy water. 

•  Decide on exact position before your remove the backing paper. 
•  Peel backing paper from decal. Press firmly on the surface. 
•  Air pockets can be pierced with a pin and smoothed.

!

WARNING

!

WARNING

!

!

WWW.PRO-DIG-USA.COM

785.856.2661

5

Summary of Contents for T15K

















Reviews: