background image

3

Pursuant to this Limited Warranty, Horizon Hobby, 
Inc. will, at its option, (i) repair or (ii) replace, any 
product determined by Horizon Hobby, Inc. to be 
defective. 

In the event of a defect, these are 

your exclusive remedies.

This warranty does not cover cosmetic damage 
or damage due to acts of God, accident, misuse, 
abuse, negligence, commercial use, or modification 
of, or to any part of the Product. This warranty 
does not cover damage due to improper installation, 
operation, maintenance, or attempted repair by 
anyone other than an authorized Horizon Hobby, 
Inc. service center. This warranty is limited to the 
original purchaser and is not transferable. In no case 
shall Horizon Hobby’s liability exceed the original 
cost of the purchased product and will not cover 
consequential, incidental or collateral damage. 
Horizon Hobby, Inc. reserves the right to inspect 
any and all equipment involved in a warranty claim. 
Repair or replacement decisions are at the sole 
discretion of Horizon Hobby, Inc. Further, Horizon 
Hobby reserves the right to change or modify this 
warranty without notice.

REPAIR OR REPLACEMENT AS PROVIDED 
UNDER THIS WARRANTY IS THE EXCLUSIVE 
REMEDY OF THE CONSUMER. HORIZON 
HOBBY, INC. SHALL NOT BE LIABLE FOR ANY 
INCIDENTAL OR CONSEQUENTIAL DAMAGES.

As Horizon Hobby, Inc. has no control over 
use, setup, final assembly, modification or 
misuse, no liability shall be assumed nor 
accepted for any resulting damage or injury. 
By the act of use, setup or assembly, the user 
accepts all resulting liability.

If you as the purchaser or user are not 
prepared to accept the liability associated 
with the use of this product, you are advised 
to return this product immediately in 
new and unused condition to the place of 
purchase.

Safety Precautions

This is a sophisticated hobby product and not a 
toy. It must be operated with caution and common 
sense and requires some basic mechanical ability. 
Failure to operate this product in a safe and 
responsible manner could result in injury or damage 
to the product or other property. 

This product 

is not intended for use by children without 
direct adult supervision.

The product manual contains instructions 
for safety, operation and maintenance. 
It is essential to read and follow all the 
instructions and warnings in the manual, 
prior to assembly, setup or use, in order to 
operate correctly and avoid damage or injury.

Questions, Assistance, and Repairs

Your local hobby store and/or place of purchase 
cannot provide warranty support or repair. Once 
assembly, setup or use of the product has been 
started, you must contact Horizon Hobby, Inc. 
directly. This will enable Horizon to better answer 
your questions and service you in the event that 
you may need any assistance.

Questions or Assistance

For questions or assistance, please direct your 
email to [email protected], or 
call 877.504.0233 toll free to speak to a service 
technician.

Inspection or Repairs

If your product needs to be inspected or repaired, 
please call for a Return Merchandise Authorization 
(RMA). Pack the product securely using a shipping 
carton. Please note that original boxes may be 
included, but are not designed to withstand the 
rigors of shipping without additional protection. Ship 
via a carrier that provides tracking and insurance for 

Limited Warranty & Limits of Liability

Summary of Contents for Pro Boat Miss LLumar





















Reviews: