background image

VISTEK V1667, V1667/SY & V1667/SY-VHS 
12-bit pal/ntsc to sdi adaptive 
comb filter decoder 

 

 

 

HU-V1667&SY&SY-VHS

 

 

 

       

15

 

 

 

7. 

TECHNICAL SPECIFICATION 

 

Analogue Input (Looping) 

 

Format   

 

 

PAL B, G, I, M, N, NTSC M, NTSC Japan, NTSC 443 

Level   

 

 

1V p-p composite (terminated) 

Connector 

 

 

BNC 

Impedance 

 

 

75

Ω

  (external) 

Return loss 

 

 

> 35dB to 5.5MHz 

 

Reference Input (Frame Synchroniser fitted) 

 

Format   

 

 

PAL B, G, I, M, N, NTSC M, NTSC Japan, NTSC 443 

Level   

 

 

Standard level Black and Burst (or 1V p-p composite) 

Connector 

 

 

BNC 

Impedance 

 

 

75

Ω

 (external) 

Return loss 

 

 

> 35dB to 5.5MHz 

 

Serial (SDV) Outputs (4) 

 

Format   

 

 

EBU Tech.3267 ANSI / SMPTE T14.22/082 

Data rate 

 

 

270 Mb/s 

Connector 

 

 

BNC 

Impedance 

 

 

75

Ω

 

Return loss 

 

 

> 15dB  5-270MHz 

Amplitude 

 

 

800mV p-p (terminated) 

DC offset 

 

 

0V +/- 0.5V 

Rise and fall times 

 

0.75-1.5 ns 

Jitter 

 

 

 

< 0.2 UI p-p 

Drive length 

 

 

up to 250m  (Belden 8281) 

 

Video Performance 

(These figures to not apply when in VHS decode mode on the V1667/SY-VHS product). 

 

Y frequency response   

< 0.2dB to 5.5MHz 

Y non-linearity   

 

< 1.0 % 

Chrominance non-linearity 

< 1.0 % 

2T pulse 

 

 

< 1 % K 

2T pulse / bar   

 

< 0.5 % K 

Chroma/luma timing error 

< 7 ns 

Subcarrier rejection 

 

> 45 dB 

Signal to noise ratio 

 

> 68 dB (weighted) 

 

Miscellaneous 

 

Power consumption 

 

8W approx. 

Frame Synchroniser 

NOT

 fitted. 

 

 

 

 

10W approx. 

Frame Synchroniser fitted. 

 
Insertion delay   

 

7µs 

 

Frame Synchroniser 

NOT

 fitted. 

Summary of Contents for VISTEK V1667




















Reviews: