Prismafood 310 NEW Instruction Manual Download Page 8

 

1.5 INFORMATION REGARDING ACOUSTIC NOISES 

The  acoustic  pressure  level  well-pondered  A  measured  on  an equal  machine,  turned  out  to  be  steady and 

lower than 70 dB (A). 

1.6 GENERAL SECURITY INDICATIONS 

Although  the  machine  is  built  in  conformity  to  the  required  security  rules  regarding  electrical,  mechanical 

and hygienic regulations it can be dangerous if: 
- used in cases and conditions different to those described by the manufacturer. 

Modifications of the proportionate covers.

 

- Inattention to the instructions of: 

Installation - functioning - usage - Maintenance. 

IMPORTANT 

Installation  and  maintenance  must  be  done  by  qualified  personnel  authorized  by  the 
manufacturer who is not responsible for any mistaken installation or manumission. 

 

1.7 SECURITY INDICATIONS 

IMPORTANT 

Carefully read the instructions before using the machine. 

WARNING 

To  avoid  dangerous  conditions  and/or  possible  injuries  caused  by:  electric  current,  mechanical 
parts, fire or hygiene problems, you must follow the safety warnings step by step. 

 

A.

 

KEEP IN ORDER YOUR WORKING AREA. Disorder can cause dangerous accidents. 

B.

  CONSIDER  ENVIRONMENTAL  CONDITIONS

.  Do  not  use  the  machine  in  humid,  wet  or  badly  lit 

environments, close to inflammable liquids or gas. 

C.

  KEEP  AWAY  FROM  CHILDREN  AND  NON  AUTHORISED  PERSONNEL

.  Do  not  permit  them  to  go  near  the 

machine or the working area. 

D.

  ONLY UTILISE THE MACHINE WITH THE CORRECT VOLTAGE

. Normal usage gives better results. 

E.

 

DRESS  IN  ADEQUATE  WAY.  Do  not  wear  hanging  clothes  or  any  items  which  can  be  caught  in  the 
machine. Use non-slip shoes. For hygiene and safety keep your hair tied back and wear protective gloves. 

F.

 

PROTECT  THE  CABLE.  Do  not  pull  the  cable  to  extract  the  plug.  Do  not  leave  the  cable  near  high 

temperatures, sharp object, water or solvents. 

G.

 

AVOID INSECURE POSITIONS. Find the best surface to ensure the machine is balanced. 

H.

 

ALWAYS PAY MAXIMUM ATTENTION. Do not be distracted when using the machine. 

I.

 

TAKE THE PLUG OUT. When the machine is not in use, before cleaning, maintenance and moving it. 

J.

 

DO NOT USE FURTHER EXTENSIONS. 

K.

 

CHECK THAT THE MACHINE IS NOT DAMAGED. Before using the machine, carefully check that all security 

devices are working. Check that: the mobile parts are not blocked, there are not any parts damaged, all 

the parts have been set-up correctly and all the conditions that could influence the regular functioning of 

the machine, are in working order. 

L.

 

REPAIRING THE MACHINE BY QUALIFIED PERSONNEL. The repairs can only be done by qualified people, 

using original spare parts. The non-compliance with these rules can represent danger for the user. 

Summary of Contents for 310 NEW


































Reviews: