INSTALLATION
1. After you have removed the unit from the carton,
inspect the unit for signs of damage. If there is
damage to the unit:
z
Notify carrier within 24 hours after delivery.
z
Save carton and packing materials for inspection
purposes.
z
Contact the Prince Castle Customer Sales
Department at 1-630-462-8800 to arrange for
a replacement to be sent.
1. Place the bin on a counter and seal its base to
the counter with food-approved sealant.
2. Insert the power cord into a proper voltage
receptacle. Note: This should be a dedicated
outlet. No other equipment should be operating
on this line (i.e. fryers, refrigerators, etc.)
3. Install the rack and pan covers into the bin. Pan
covers are used for pans that hold grilled,
broiled, or baked meat products. Do not install
the pan cover on pans that hold fried foods.
4. Turn the power switch on. Allow 30 minutes for
warm-up.
THE TEMPERATURE CONTROL
PANEL
1. Indicators and Displays
Within the four character digital display there are
LED indicators. The four character digital dis-
play shows the numerical value of the tempera-
ture, and the LED indicators display the follow-
ing:
•
The LED indicator next to the
UPR HTR
(for
the
UPPER HEATER)
is on when the tem-
perature being displayed is for the upper
heater.
•
The LED indicator next to the
PROG
is on
when in the Program Mode.
•
The LED indicator next to the
LWR
HTR
for
the
LOWER HEATER
) is on when the tem-
perature being displayed is for the lower
heater.
•
The LED indicator next to the
HEAT
is on
when power is applied to the selected heater.
2. Control Panel buttons and LED indi
cators
•
SET POINT
: The set-point temperature is
displayed for the selected heaters when this
button is pressed during the operating mode.
The SET POINT LED indicator will be on
when the Set-point mode is selected. Press
and hold the Prince Castle button then press
and hold the SET-POINT button to program
the temperature for the selected heater
.
•
ACTUAL TEMP:
The actual temperature is
displayed for the selected heaters when this
button is pressed during the operating mode
and the ACTUAL LED indicator will be on.
•
UP ARROW
and
DOWN ARROW
: When
pressed in the operating mode, will scroll
through the upper and lower heaters for all
four cavities to display either the actual or
set point temperature. The LED next to the
UPPER SHELF
or
LOWER SHELF
will be on
to indicate which heater is being selected.
The letters
A
,
b, C,
and
d ( A & B for 2
Shelf Units)
are displayed to show the
selected cavity location for the upper and
lower heaters.
When reading the digital display from left-to-right,
the following information is displayed: The
Upper
or
Lower
heater for the
selected
cavity (
A, b,C,or
d
)(A & B for 2 shelf units
, if power is being applied
to the
heat
er, and if the display temperature is the
ACTUAL
or
SET
-
POINT
temperature.
PROGRAMMING
The temperature adjustment range for a heater is:
OFF, 150
°
F to 225
°
F (OFF, 65
°
C to 107
°
C ). The
recommended starting setpoint temperatures are:
•
190
°
F (88
°
C) for the Upper Shelves.
•
190
°
F (88
°
C) for the Lower Shelves.
•
NOTE
: Through testing, these temperatures
may be increased or decreased as long as
the food quality and desired temperature of
the product being tested is maintained.
Programming Set Point Temperatures
1. Press and release the
UP
or
DOWN
arrow button
until the heater in the cavity to be changed is
selected.
2
545-502revB
Printed i
n
USA 1/06 © 2006