manualshive.com logo in svg

Primus FS 6-16, Installation Manual, Page: 19 / 30

Share
Download
Primus FS 6-16 Installation Manual Download Page 19

18

INSTALLATION AND MAINTENANCE MANUAL

PUBLICATION DATE  Sep 05    100646

1. Terminals for connection

liquid soap pumps

2. Neutral line

3. Soap signals

Fig. 4.7.B. Electrical connection soap pumps

4.8. PREPARING THE MACHINE FOR OPERATION

CHECKING BEFORE PUTTING INTO SERVICE

1. Make sure the transporting braces are removed.

2. Put out all things from wash drum.

3. Check the machine horizontal position.

4. Check connection and clearance of your drain, channel or central drainage.

5. Check protective connection (earthing) and electrical supply connection.

6. Open water valves to machine and check hose and connections for leaks.

7. Read carefully the „User´s manual“ and „Programming manual“, which are a part of delivery.

8. Initialize the programmer after machine installation. The calibration of the zero level must not happen

anymore. This calibration is executed in the factory and is not changeable.

9. Check the drum rotation direction during extracting according to the extracting label.

10. Check the vibration switch function during extracting (see also chapter 5.2 adjustments and parts

exchange, adjustment of the vibration switch.

11. Check the emergency function.

Summary of Contents for FS 6-16































Reviews:

No comments