background image

11

70283601

Operation

Emergency Stop Button On 
European Models

(Manual Timer and OPL Micro Models Only)

IMPORTANT: All manual timer and OPL Micro 
operated tumblers are factory equipped with an 
emergency stop button located on the front panel.

Figure 2 

To operate emergency stop button:

a. Press red emergency stop button to stop all 

action.

b. To restart machine, pull red emergency stop 

button out and press START pad or button.

NOTE: Activation of the emergency stop button 
stops all machine control circuit functions, but 
DOES NOT remove all electrical power from 
machine.

Operating Instructions

IMPORTANT: Clean lint screen and lint 
compartment daily.  Failure to clean the lint screen 
daily will result in higher than normal 
temperatures that may damage laundry.

Step 1: Clean Lint Screen/Compartment

Remove any accumulated lint from the lint screen and 
compartment. Close panel tightly against tumbler 
frame and lock panel securely, if applicable.

Step 2: Load Laundry

Open loading door and load cylinder with laundry. DO 
NOT OVERLOAD.

NOTE: Overloading causes slow drying and 
wrinkling.

Close loading door. Tumbler will not operate with the 
door open.

Step 3: Determine Required Temperature

The type of fabric being dried will determine the 
setting. Consult the fabric-care label or fabric 
manufacturer to determine proper temperature setting.

IMPORTANT: Always follow the fabric care 
instructions supplied by the garment 
manufacturer.

Step 4: Determine Control Type

Refer to the following pages and use the appropriate 
instructions for the control type.

To reduce the risk of fire: 
• DO NOT DRY articles containing foam rubber or similarly textured rubberlike materials.
• DO NOT DRY plastics, anything containing wax or chemicals such as mops and cleaning 

cloths, or anything dry-cleaned at home with a dry-cleaning solvent.

• DO NOT TUMBLE fiberglass curtains and draperies unless the label says it can be done. If 

they are dried, wipe out the cylinder with a damp cloth to remove particles of fiberglass.

W076

To reduce the risk of serious injury, allow cylinder to stop before cleaning lint screen.

W412

WARNING

TMB1666N

1

Emergency Stop Button

1

Summary of Contents for D55
























Reviews: