Primary fluid systems ECO-25 Instruction Manual Download Page 11

 

11 

 

LIMITED WARRANTY 

 

Primary Fluid Systems Inc. (Primary) warrants its products against defects in workmanship or materials for one (1) year under 
normal use. Three-(3) year available when application card is completed and returned to factory. 
 

Primary’s obligations and liabilities under this warranty shall be limited to replacement of the product, or a refund 

of an amount not 

to exceed the purchase price of the product(s) to which such warranty claim is made. Repairs or replacements are made subject to 

our inspection of the returned product(s). Primary’s decision of one of these alternatives shall be the buyer’

s exclusive remedy. 

 
This warranty does not extend to damage by corrosion or other decomposition by chemical action. Primary does not warrant 
damages caused by (a) improper use of the product, (b) unauthorized modification or attachment to product, (c) misuse, abuse, 
accident or negligent handling or installation of product, or (d) alterations or repairs made by purchaser. 
 
The materials of construction offered are recommendations only, subject in all cases to acceptance by purchaser. These 
recommendations do not constitute any guarantee against corrosion or decomposition, but are based on previous experience and 
best available information of the industry. 
 
Statements and instructions set forth herein are based on the best information and practices known to Primary, but it should not be 
assumed that every acceptable safety procedure is contained herein. Of necessity Primary cannot guarantee that actions in 
accordance with such statements and instructions will result in the complete elimination of hazards and it assumes no liability for 
accidents that may occur. 

 

Except as specifically provided herein, Primary makes no warranty, representations, promise or guarantee, either express or 
implied, statutory or otherwise, with respect to the product and 

technical information provided,  including the products’ quality, 

performance, merchantability, or fitness for a particular purpose. 

 

In no event will Primary be liable for indirect, special, incidental, economic, covert or consequential damages arising out of the use 
or inability to use the product, including without limitation, damages or costs relating to the loss of profits, business and good will 

even if advised of the possibility of such damages. In no event shall Primary’s liability exceed the amount

 paid by you for the 

product. 

 

The warranty and remedies set forth herein are exclusive and in lieu of all others, oral or written, express or implied. No Primary 
dealer, distributor, agent or employee is authorized to make any modification or addition to this warranty. This warranty gives you 
specific legal rights and you may also have other rights which vary from state to state. 
 

 

Summary of Contents for ECO-25













Reviews: