background image

>

Connecting the A30.1 Integrated Amplifier

8

P O W E R   C O N N E C T I O N

Warning

: Before connecting power check that the required supply voltage,

indicated on the back panel, corresponds to your local AC supply. If a

different voltage is stated on the type plate do not connect the amplifier to the

mains power, and seek advice from your dealer.

Connect the mains power using the enclosed mains cable.

Note

: Always disconnect the amplifier from the mains power before

connecting or disconnecting any of the cables.

O U T P U T S

Loudspeaker outputs

Connect the left and right loudspeakers to the corresponding terminals. The

terminals can accept speaker cables terminated with 4mm banana plugs,

spade terminals, or bare wires. To connect bare wires unscrew the terminal,

pass the bare wire through the hole in the terminal bolt, and clamp the wire in

place by screwing the terminal back down.

Preamplifier outputs

The preamplifier output sockets provide a line-level output from the A30.1

preamplifier stage which can be connected to another power amplifier, such

as the Primare A30.2. The level of this output is controlled by the volume

control on the A30.1.

The TAPE OUT sockets provide a fixed level copy of the currently selected

source, suitable for connecting to a tape recorder.

The TAPE1 OUT sockets provide a fixed level copy of the currently selected

source, or a copy of the TAPE1 input, depending on the position of the

MONITOR

 switch.

I N P U T S

Source inputs

Connect each source to the appropriate source input, connecting the right

channel to the red socket and the left channel to the white socket.

To connect an analogue turntable with a moving magnet or moving coil

cartridge you will need an additional phono preamplifier such as the Primare

R20. The output of the turntable is connected to the R20, and the output of the

R20 should be connected to a spare input on the A30.1, such as AUX.

A ground terminal is provided below the input sockets to allow you to provide

a direct ground connection for sources in order to remove hum loops.

§3 Connecting

14/5/01, 2:00 pm

8

Summary of Contents for A30.1















Reviews: