Prima LPR 712, Instruction Booklet

Page: 8 / 28

8
The selector dial can be turned either clockwise or
anticlockwise.
Position
Eco in cottons and synthetics sectors
corresponds to the ENERGY SAVING programmes and
position «Cold» to “cold wash”.
At the end of the programme the selector dial must
be turned to position “
o
” (reset) and the “On/Off”
button must be pressed to switch the machine off.
Functions
Altering an option or a running programme
It is possible to change any option before the
programme carries it out.
Before you make any change, you must pause the
washing machine by pressing the “
Start/Pause” button.
Changing a running programme is possible only by
resetting it. Turn the programme selector dial to "
o
" and
then to the new programme position. The washing water
in the tub will not emptied out .
Start the new programme by pressing the “
Start/Pause”
button.
Interrupting a programme
Depress the “ Start/Pause” button to interrupt a
programme which is running: the corresponding light
starts to flash.
Depress the same button to restart the programme.
Opening the door after the programme has
started
You can open the door, after having set the washing
machine to PAUSE, provided the following conditions
exist:
• the washing machine has not heated beyond 55°C;
• the level of the water is not high;
If these requirements are met, when you pause the
washing machine, the door can be opened.
Should it not be possible to open the door, and should it
be absolutely necessary to do so, switch the machine off
by pressing the “
On/Off ” button.
After approximately 3 minutes, you can open the door.
Pay attention to the level and temperatures of the
water in the washing machine!
When you close the door and press the “ On/Off ” button
again, the washing machine will resume the programme
from the point where it had been interrupted.
End of “Soak 30” programme
At the end of the soak time, the machine stops
automatically
with water left in the tub . The light of
the “ Start/Pause ” button goes off and the pilot light
“ End” in the programme progress display is alight but
the door is locked to indicate that the water must be
emptied out.
Before starting a new washing phase, it is necessaty to
empty out the water by:
●
draining only. Select programme “ Drain” and press
Start/Pause button , the water is emptied out without
spinning, or
●
draining and spin. Select programme “ Spin” .
Reduce the spin speed by means of the relevant
button and then press
Start/Pause button. The water
is empty out and the laundry is spun at the selected
spin speed.
At the end of the cycle, the light “ End ” illuminates, the
door can be opened.
Important !
At the end of the « Soak 30 °» programme you can select
the washing programme. First, turn the programme
selector dial to
“
o
” (Reset), then select the programme.
Programme information
“Handwash” (wool)
Washing programme for machine washable wool as
well as for hand washable woolens and delicate fabrics
with the “hand washing” care symbol.
“Soak 30°”
This is a special programme for heavily soiled laundry.
The machine performs a soak of about 30 minutes at
30°C. At the end of the soak time the machine will stop
automatically
with water left in the tub. Pour the
detergent for the soak programme into the compartment
marked .
This programme
cannot be used for very delicate
fabrics or Wool.
Before starting a new washing phase, it is necessary to
empty the water by selecting the “
Drain ” programme.
“Rinses”
With this programme it is possible to rinse and spin
cotton garments which have been washed by hand.
The machine performs 3 rinses, followed by a final spin
at 1200 r.p.m. The spin speed can be reduced by pressing
“
Spin ” button.
132967680.qxd 31/10/2007 14.40 Pagina 8