background image

US Jet 3 Ultra/RevC/Jun03

                            www.pridemobility.com

31

How can I ensure maximum battery life?

A fully charged deep-cycle battery will provide reliable performance and extended battery life. Keep your power chair’s

batteries fully charged whenever possible. Batteries that are regularly and deeply discharged, infrequently charged, or

stored without a full charge may be permanently damaged, causing unreliable power chair operation and limited battery life.

How should I store my power chair and its batteries?

If you do not use your power chair regularly, we recommend maintaining battery vitality by charging the batteries at least

once per week.

If you do not plan on using your power chair for an extended period, fully charge the batteries prior to storage. Disconnect

the battery harnesses and store the power chair in a warm, dry environment. Avoid temperature extremes, such as freezing

and excessively hot conditions, and never attempt to charge a frozen battery. A cold or frozen battery should be warmed

for several days prior to recharging.

What about public transportation?

AGM and Gel-Cell batteries are designed for application in power chairs and other mobility vehicles. These batteries are

Federal Aviation Administration (FAA) approved, allowing safe transportation on aircraft, buses, and trains, as there is no

danger of spillage or leakage. We suggest you contact the carrier’s ticket counter in advance to determine that carrier’s

specific requirements.

What about shipping?

If you wish to use a freight company to ship your power chair to your final destination, repack your power chair in the

original shipping container and ship the batteries in separate boxes.

V I I .   B A T T E R I E S   A N D   C H A R G I N G

Summary of Contents for Jet3 Ultra
















































Reviews: