Pride Mobility Quantum Q6 Edge 2 Installation Instructions Manual Download Page 8

Section 2: Operation

These instructions are from the DAHL User Manual located at

https://dahlengineering.dk/media/238906/503744-dahl_manual_mkii_uk_420.pdf

8

To use the system, maneuver the wheelchair slowly and in a uniform direction over the docking 
station. The lock plate under the wheelchair helps to guide the wheelchair into place in the 
docking station. When the lock plate is fully engaged in the docking station, a spring-action 
locking pin automatically secures the lock plate.

The docking station is equipped with a control switch that indicates whether the lock plate is 
correctly secured in the docking station. As soon as the lock plate comes into contact with the 
locking pin, a warning tone will sound (a high-pitched howl), and the red diode/lamp (LED) in the 
control panel will light up until the lock plate is either fully engaged or else the wheelchair is 
removed from the docking station.

As an indication that the wheelchair is properly secured, the warning tone will cease, the red 
diode in the control panel will go out and the green diode lamp (LED) will light up.

When the wheelchair is correctly secured, the safety belt should be fitted and adjusted so that it 
fits the user.

Perform a check of the wheelchair

1

Perform a final check by connection the wheelchair to the docking station. Check that it is 
securely locked and make sure that all release methods work as intended. (Figure 1)

Securing the wheelchair in the docking station

 

Green LED

Red LED

Control panel

Shutter Button

See drawing 501862 for 

electrical diagram

Manual operating lever

Wheelchair, max. weight 200 kg

Warning sound

See drawing no. 501733

Figure 1.

1

2

3

Do not drive the vehicle whilst a wheelchair is being maneuvered into position in the docking 
station. In general, do not use the vehicle if the wheelchair is not correctly secured, the warning 
tone sounds and/or the red warning lamp (LED) in the control panel flashes or is lit! Therefore, 
always check if the lock plate is properly engaged in the docking station by trying to back the 
wheelchair out of the docking station before moving the vehicle. (It must not be possible to back 
out of the docking station without pressing the red button in the control panel). 

4

1

2

3

8

9

7

6

4

5

Summary of Contents for Quantum Q6 Edge 2












Reviews: