PREVOST LE MIRAGE XLII, Maintenance Manual

Page: 1297 / 1342

Section 26: XLII SLIDE-OUT
PA1553 3
19 SLIDE-OUT MAXIMUM LOAD.............................................................................................................. 39
20 CONVERSION CHECKLIST ................................................................................................................. 40
20.1 E
RROR
C
ONDITION
O
R
M
ISSING
O
PERATION
C
ONDITION
................................................................... 41
20.2 T
ROUBLESHOOTING
– O
PERATING
C
ONDITIONS
& C
ONTROL
............................................................. 41
20.3 T
ROUBLESHOOTING
- M
ECHANICAL
C
OMPONENTS
............................................................................ 43
20.4 S
LIDE
-O
UT
F
AULT
M
ESSAGE
O
N
M
ESSAGE
C
ENTER
D
ISPLAY
(M
CD
)................................................. 46
LIST OF ILLUSTRATIONS
FIGURE 1 : FRONT SLIDE-OUT.................................................................................................................. 5
FIGURE 2 : REAR SLIDE-OUT .................................................................................................................... 5
FIGURE 3 : SIDE INNER STOPPER ADJUSTMENT .................................................................................. 5
FIGURE 4: UPPER INNER STOPPERS ADJUSTMENT.............................................................................. 5
FIGURE 5: LOWER "IN LIMIT" STOPPER................................................................................................... 6
FIGURE 6: UPPER "IN LIMIT" STOPPER .................................................................................................... 6
FIGURE 7 : EXTERIOR EXTRUSION .......................................................................................................... 6
FIGURE 8: SECURITY PIN AIR CYLINDER REMOVAL .............................................................................. 7
FIGURE 9 : FRONT SLIDE-OUT ROOF REINFORCING ROD ................................................................... 7
FIGURE 10 : RACK....................................................................................................................................... 8
FIGURE 11: PINION AND KEYLESS BUSHING POSITIONING .................................................................. 9
FIGURE 12: PINION AND KEYLESS BUSHING AS SEEN FROM EVAPORATOR COMPARTMENT........ 9
FIGURE 13: MECHANICAL COMPONENTS (TYPICAL) ............................................................................. 9
FIGURE 14 : KEYLESS BUSHING TIGHTENING ..................................................................................... 10
FIGURE 15 : TORQUE WRENCH FORMULA ........................................................................................... 10
FIGURE 16 : KEYLESS BUSHING INSTALLATION INSTRUCTION ......................................................... 12
FIGURE 17: ELECTRIC MOTOR AND SPEED REDUCTION GEARBOX ................................................. 13
FIGURE 18: DRIVE MOTOR/GEARBOX ASSEMBLY MOUNTING BOLTS .............................................. 13
FIGURE 19: CLAMPING HUB POSITION ON GEARBOX SHAFT ............................................................. 14
FIGURE 20: JAW COUPLING..................................................................................................................... 14
FIGURE 21: SLIDE-OUT LEVEL ADJUSTEMENT ..................................................................................... 15
FIGURE 22 : SLIDE-OUT LEVELING......................................................................................................... 16
FIGURE 23: TILT ADJUSTMENT ............................................................................................................... 16
FIGURE 24 : RAIL POSITIONING............................................................................................................... 17
FIGURE 25: ACETAL PLASTIC BLOCKS................................................................................................... 17
FIGURE 26: REMOVE THE UPPER ACETAL PLASTIC BLOCKS WITH A PICKING TOOL ..................... 17
FIGURE 27: LOWER ACETAL PLASTIC BLOCK INSERTION .................................................................. 18
FIGURE 28 : FRONT SERVICE COMPARTMENT.................................................................................... 19
FIGURE 29: PNEUMATIC COMPONENT PANEL...................................................................................... 20
FIGURE 30 : SEAL ASSEMBLY................................................................................................................. 20
FIGURE 31: REAR SLIDE-OUT INFLATABLE SEAL AIR INLET ............................................................... 21
FIGURE 32: SLIDE-OUT 2" INSIDE – UPPER PART ................................................................................. 22
FIGURE 33 : DASHBOARD SLIDE-OUT TELLTALE LIGHT ..................................................................... 23
FIGURE 34: MAIN BREAKER IN ENGINE R.H. SIDE ACCESS COMPARTMENT.................................... 23
FIGURE 35 : SLIDE-OUT CONTROL PANEL............................................................................................23
FIGURE 36 : VEC CIRCUIT BREAKERS & FUSES .................................................................................. 24
FIGURE 37 : FRONT SLIDE-OUT SENSORS ........................................................................................... 25
FIGURE 38: REAR SLIDE-OUT SENSORS ............................................................................................... 25
FIGURE 39 : MAGNETS ON SLIDE-OUT UNDERBODY.......................................................................... 25
FIGURE 40 : SLIDE-OUT PANELS AND WINDOWS ................................................................................ 26
FIGURE 41 : SIDE PANEL INSTALLATION – DOUBLE FACE ADHESIVE TAPE APPLICATION ON THE
SLIDE-OUT STRUCTURE................................................................................................................... 27
FIGURE 42 : SIDE PANEL INSTALLATION – SIKA 206 G+P APPLICATION.......................................... 27
FIGURE 43 : SIDE PANEL INSTALLATION – SIKA TACK+BOOSTER APPLICATION.......................... 27
FIGURE 44 : SIDE PANEL INSTALLATION ............................................................................................... 28