Charging
Make sure the product
is power-off before the
charge. The charge lasts
about 5 hours.
It’s better for the product not to be connected to the power supply
for more than 24 hours. (Remark: The indicator light will not change
or turn off when it is fully charged.)
1. Insert the product charger into the PreShave Power Cleanser.
2. Plug in the charger.
3. The charge indicator lights up (See diagram above).
4. After the full charge, unplug the charger and also pull off the
product’s plug from the Power Cleanser.
Specifications
Input: 100-240V~50/60HZ Battery: Ni-Cd Battery
Output: 6.5VDC 600mA
Using SonicDermabrasion
®
Daily Treatment
Preshave
Dampen face with warm water, or apply shaving cream or preshave
conditioner. Use the PreShave Power Cleanser in a circular motion
ending in an upward stroke to help lift the beard up and away from
the face. Press Power Button once for low-speed or press again
for high-speed. Speed setting is dependent on sensitivity of skin
type, beard length and hair type. Gently rinse skin thoroughly after
each use with warm water and pat dry. Apply shaving cream and
shave. Finishing touch - a good, close-shave followed by the right
facial wash and aftershave moisturizer to help achieve optimum
skin health.
Exfoliation
Dampen face with warm water, or with cleansers, scrubs and
microdermabrasion crèmes - dot face in five (5) areas: forehead,
each cheek, chin and nose lightly, spread evenly over face with
fingertips. Press firmly to treated area and move PreShave Power
Cleanser in an upward, circular motion. Recommended time per
treated area is 20 seconds for each area. Gently rinse skin
thoroughly after each use with warm water and pat dry.
Micro-Fiber Bristle Triple Brush Heads– Attach and Remove
To attach Brush Head, align inner pin at center of brush head
housing to the center opening on the head of the device. Holding
the device handle, press from the center of the brush head and
push down until it snaps into place.
Align Brush Head onto Device as shown.
To remove the Brush Head, simply grip the
outer plastic base of the Brush Head firmly
in one hand and the device handle in the
other hand – then pull up evenly.
This ISM device complies with Canadian ICES-001. Cet appareil
ISM est conforme à la norme NMB-001 du Canada. This Class B
digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe B est conforme à la norme NMB-003 du Canada.
Caring For Your SonicDermabrasion
®
PreShave Power Cleanser
Micro-Fiber Bristle Brush Heads
1. Clean Brush Heads after every use. Remove Brush Heads, rinse
clean with warm water and mild soap to remove any build-up
that may have accumulated, shake off excess water and towel
dry – or gently rub the Brush Head against a towel for 5 -10
seconds while the SonicDermabrasion is on. Do not attach
wet brush heads to handle while charging.
2. Do not allow liquid cleansers or moisturizers to accumulate on
Brush Heads.
3.
To clean, place a small amount of shampoo onto fingertips, then
work into bristles, rinse clean and air or towel dry.
Replace Brush Heads as needed – depending on use, a brush head
should last between 3-4 months, they can be purchased from
your retailer or online at www.pretika.com.
Facial Brush Handle
1. Do not use abrasive cleaners or chemicals to clean any part of
the Sonic Dermabrasion.
2. Clean handle with damp cloth – using mild detergent or warm
water and towel dry immediately.
*DO NOT IMMERSE CHARGING ADAPTOR IN WATER. ADAPTOR CONNECTOR MUST REMAIN DRY
AT ALL TIMES.
NOTE:
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE
USER AUTHORITY TO OPERATE THE EQUIPMENT
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
