background image

128-8112

2 of 8

2

Some of the more popular options available for the unused Option
Buttons of your transmitter are:

AS 9075

Remote car starter

AS 9153

Remote window roll up

AS 9256

Remote trunk release relay

Although the most common use of the transmitter buttons are shown
on the front page of this guide, any button or button combination can be
programmed into any receiver channel.  Additionally,  if all 4 buttons are
used and you require access to a 5th channel, you would program a
combination of buttons to control the 5th function.   i.e... you have
programmed lock for arm, unlock for disarm, trunk for trunk release,
and OPT1 for garage door operation, and you've added a window up
module that you want independent control of, you would program un-
lock and trunk buttons pressed simultaneously into the receiver to con-
trol this function independently.  Also, if you do not program a transmit-
ter button into channel 2 which is the separate unlock/disarm chan-
nel, then whatever button is programmed into channel 1 will serve
as both lock/arm & unlock/disarm.

PROGRAMMING TRANSMITTERS:
NOTE:

It is important to remember that during the programming mode,
each individual step must be completed within 15 seconds of
the previous step.  If the 15 second time limit expires between
steps, the unit will automatically exit the program mode. This
is indicated by a long chirp from the siren.

Non alarm models will flash the parking lights only to confirm the
transmitter code has been learned and stored.

NOTE:

Because the system may be capable of sounding a siren, the
vehicle horn, or both, where the siren chirp is referenced be-
low, the siren may chirp, the horn may beep, or both devices
may sound.

Note: 

 Some systems are capable of single button programming, if your

alarm module is capable of this feature, simply complete step 4
of these programming instructions for each transmitter you wish
to control your system and exit the program mode by switching
off the ignition key.

TO PROGRAM ADDITIONAL TRANSMITTERS:

1) Enter the vehicle, and turn the ignition switch to the on position.
2) Press and release the valet push button switch three times.

Note:

 Some systems may use a combination push-button LED

switch.  In these systems the push-button and the dash mounted
LED are one and the same.

3) The dash mounted LED will flash 1x, and the siren will chirp 1x,

indicating that the system is ready to accept programming of channel
#1 which is arm/lock, disarm/unlock/unlock 2, and panic functions.

Summary of Contents for Prestige 07S3BP









Reviews: