background image

128-9480

11 of 16

Page 11

SELECT

ABLE FEA

TURES

The selectable features of this unit can be set manually as explained on the previous page.

Factory default settings are indicated by 

BOLD

 text below

.

  NOTE: 

 

Manual programming Keyless Entry Models with no horn output will Flash the Parking Lights instead of chirp where chirp is indic

ated.

 

Also, no data will be indicated if a feature is not available for a particular model. 

The unit will enter the feature but no selection will be available.

Feature Selection

 

 

1 Chirp

 

 

2 Chirps

 

 

3 Chirps

 

 

4 Chirps

 

 

5 Chirps

 

 

6 Chirps

 

 

1st DoorL/UL

 

 

1S/1S

 

 

3.5 Sec.

 

 

500mS L, Dbl. U/L

  

Dbl L, 500mS UL

 

Dbl L, Dbl UL

 

500mS/350mS ul

 

2nd Accy 

Lock

 

 

Not A

vailable

3rd Accy

. UL

 

 

Not A

vailable

4th Headlights

  

Not A

vailable

5th Passive Locks

 

 

Not A

vailable

6th 

Pass/Act 

Arm

 

 

Not A

vailable

7th Siren/Horn

 

 

Not A

vailable

8th Horn Chirp

 

 

Not A

vailable

9th O/R Method

  

Not A

vailable

10th 2 Step U/L

  

Not A

vailable

11th Chp Del 

Tx

 

 

Not A

vailable

12th 

Trigger 

Circuits

  

Not A

vailable

13th L/UL

 Poll

 

 

Not A

vailable

14th 

Aux Ch 5 Sel

 

 

Not A

vailable

15th 

Aux Ch 6 Sel

 

 

Not A

vailable

16th 

Aux Ch 7 Sel

 

 

Not A

vailable

17th T

rigger 

Delay

 

 

Not A

vailable

18th DBI/ADS Select

 

DBI 

19th PK Lt/ 

Tnk Rel Swap

 

 

Not A

vailable

Summary of Contents for 1124316

















Reviews: