Prestige 1122242 Installation Manual Download Page 1

128-9482

1 of 16

Page 1

Model  APSRS3Z

Installation Manual

PATENTED:  www.voxxintl.com/company/patents

Table Of Contents:

Before You Begin 

Page 2

Wire Harness Quick View 

Page 3

Installation Of The Major Components 

Page 4

6 Pin Power Harness 

Page 5

Door Lock / Unlock Harness 

Page 6 & 7

12 Pin Input/Output Harness 

Page 7 - 9

4 Pin Main Harness 

Page 9

Tachometer Programming Information 

Page 10

Transmitter Programming Information  

Page 10

Feature Bank 2 Program Information 

Page 10 & 11

Feature Bank 3 Program Information 

Page 12 & 13

Diagnostics 

Page 14

Data Bus Port Information 

Page 14

Completing The Installation 

Page 14

Circuit Wiring Diagram 

Page 16

FCC COMPLIANCE

 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 

 (1) This device may not cause harmful interference, and 

 (2) this device must accept any interference received, including interference that may cause undesired operation.

 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These 

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses 

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to 

radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause 

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to 

try to correct the interference by one or more of the following measures:

 —Reorient or relocate the receiving antenna.

 —Increase the separation between the equipment and receiver.

 —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 —Consult the dealer or an experienced radio/TV technician for help.

 Warning!

 Changes or modifications made to this equipment not expressly approved by the part responsible for compliance could void the use’s author

-

ity to operate the equipment

 NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this 

 equipment. Such modifications could void the user’s authority to operate the equipment.

Summary of Contents for 1122242

















Reviews: