background image

 

Page 

6

 of 

12

 

 

Electrical connection 

3L2

1L1

5L3

4T2

2T1

6T3

(N) 8T4

(N) 7L4

L1

L2

L3

N Grnd

1.

2.

3.

4.

 

Figure 5. ExitOxy switch panel 

 

 

The ExitOxy needs a supply of ± 400V AC + N 16A

 

Before the ExitOxy can be supplied, the following points must be checked: 

-

 

Is there a correct main power cable supplied? 

The ExitOxy is delivered without its own power cable. It is therefore desirable the an authorized electrician provides 
a correct main power supply cable to the location of the ExitOxy. 

 

-

 

Is the supplied power cable voltage-free? 

Use a fitting voltmeter or multi-meter to check if the cable is voltage-free. Is there a voltage? Let an authorized 
electrician shut off the power.

 

-

 

Is the head switch in the ‘OFF’ position? 

(Figure 5. No. 1 & Figure 6)  

Put this, if needed, in the desired position.

 

If the above points are met, the supply can be safely connected.

 

I  ON

O

  O

FF

 

Figure 6. Main switch 

 

 

Step 1. Insert the supplied power cable into the ExitOxy switch panel. 
Finish the cable with a suitable cable tray or PVC pipe.  

Step 2. Connect the phases 1, 2 and 3 to the contacts 2T1, 4T2 and 6T3 of the main switch (Figure 5). 

Step 3. Connect the neutral wire to the contact (N)8T4 of the main switch (Figure 5). 

Step 4. Connect the green/yellow wire to the first ground terminal of the terminal strip. (Figure 5. No. 2). 

 

Summary of Contents for ExitOxy













Reviews: