Presidential Billiards ADDISON Install Instructions Download Page 1

 

 

 

 

INSTALL INSTRUCTIONS FOR ADDISON AND BILTMORE CABINETS 

 
Tools required by the installer: 
3/8” Drive ratchet and Extension 

 

 

1/2” Sockets for above 

1/2” Combo end wrench 

 

 

 

# 2 and # 3 Phillips screwdriver 

Electric drill/ driver   

 

 

 

1/8” & 3/16” Drill bits 

Speed Square 
 
Prior to installation of the table please check for damaged or missing parts. Call Presidential Billiards at 
866-728-2253 if there is a problem. The assembly hardware is packed according to the steps below to 
facilitate the cabinet assembly. 
 

 

STEP 1

 

ASSEMBLE THE CABINET 

1.1 

Lay the cabinet panels upside down on a clean, flat, level surface. 

1.2 

Loosely assemble the leg and beam bracket to cabinet panels. 

1.3 

Once cabinet is loosely assembled, place top corner bracket in position. 

 

Do Not

 Tighten cabinet at this time   

 

STEP 2

  

ATTACH BEAMS

 

 
2.1 

Place beams in beam brackets. 

2.2 

Use bolt, square washer, round washer and nut from hardware pack to fasten beam to beam 
bracket. 

2.3 

Using a square pull the beam flush with the top of the cabinet while making sure the bottom of 
the beam in resting fully on the bracket.  

2.4 

Tighten beam to the bracket. 

2.5 

Tighten the bracket to the cabinet. (Note: Long beam must be flush or slightly below short cross 
beams or slate will not set level on table.) 

2.6 

Starting in one corner tighten bolts in leg and corner brackets. Use a square to make sure the 
corner bracket is flush or slightly below the top of the cabinet. 

2.7 

Attach wing blocks using 5/16” x 2” bolts and 5/16” flat washers from hardware pack. 

 
STEP 3      INSTALLING TRIM CORNERS  

3.1 

Start screws in corners with fingers. 

3.2 

Slide corners into position. 

3.3 

Using #2 Phillips screwdriver, tighten the screws. (

DO NOT USE POWER TOOLS) 

Tighten 

until snug. 

Summary of Contents for ADDISON






Reviews: